Woods RB750-4 Скачать руководство пользователя страница 30

Страница: 30 / 54

Assembly

MAN0160 (Rev. 8/19/2005)

Install Pneumatic Tail Wheel 28775
(Optional) Cont’d

Figure 23

Pneumatic Tail Wheel Installation

14.

Cap Screw, 1/2 NC x 1-3/4 GR5

15.

Tail Wheel Arm Assembly

16.

Cap, Dust

17.

O-Ring .09 x 1.56 OD

18.

Bushing, Bronze 1.5 x 1.63 x 1.50

19.

Grease Fitting, 1/4-28 Tapered Thread

20.

Grease Fitting, 1/8 Pipe Thread

21.

Plate, Top Dampener

22.

Disc, Friction 4 x 6.15

23.

Pin, Spirol 7/16 x 2-1/2

24.

Wheel Yoke Assembly

26.

Washer, Flat 1” Standard

Link, Floating Right

Link, Floating Left

Sleeve, 1.00 x 1.25 x 1.44

Pin, Clevis 1 x 4-29/32 HT

Washer, Flat 1” SAE

Pin, Cotter 1/4 x 2-1/4

Ratchet

Tail Wheel Bracket Assembly

10.

Pin, Clevis 3/4 x 12-1/4

11.

Pin, Clevis 1 x 12-1/4

12.

Washer, Flat 3/4 Standard

13.

Pin, Cotter 1/4 x 1-1/2

Содержание RB750-4























































Результаты поиска

Содержание RB750-4

Отзывы:

Похожие инструкции для RB750-4

Бренды по названию

Популярные бренды

Woods RB750-4, Руководство оператора

Результаты поиска

Содержание RB750-4

Отзывы:

Похожие инструкции для RB750-4

Бренды по названию

Популярные бренды