Woods RB750-4 Скачать руководство пользователя страница 29 | Manualshive

Страница: 29 / 54

background image

Assembly

29

MAN0160 (Rev. 8/19/2005)

OPTIONAL EQUIPMENT - ALL MODELS

Install Pneumatic Tail Wheel 28775
(Optional)

IMPORTANT

■

When grading with tail wheel attached, do not

attach upper link of tractor 3-point hitch to blade
without using floating links (2 & 3). Without float-
ing links, equipment damage may result and void
warranty.

Refer to Figure 23.

The tail wheel is very helpful for finish grading and
leveling work. The ratchet controls the approximate
cutting height.

1.

Remove top link of tractor 3-point hitch.

2.

Attach float links (2 & 3) and sleeve (4) to inside

of the top holes of A-Frame. 3/4 dia. welded pin on
side of float links must face outward and be located
on the bottom end.

NOTE:

Do not use with Category 2 quick-attach cou-

plers.

3.

Secure into position with top link pin.

4.

Attach bracket (9) to boom assembly with clevis

pin (10), two flat washers (12) and two cotter pins
(13). Secure together with cap screw (14).

5.

Attach tail wheel arm (15) and yoke (24) to

bracket (9) with clevis pin (11), washers (26), and cot-
ter pin (13).

6.

Attach ratchet (8) between bracket (9) and tail

wheel arm (15). Secure with pins supplied with
ratchet.

7.

Attach top link to float links (2 & 3) using clevis pin

(5), two SAE flat washers (6), and cotter pins (7).

«
...
27
28
29
30
31
...
»

Содержание RB750-4























































Отзывы:

Нет отзывов

Похожие инструкции для RB750-4

Бренд: Navman Страницы: 17

Бренд: 3M Страницы: 2

D-IMager EKL3104

Бренд: Panasonic Страницы: 13

Бренд: Labokey Страницы: 5

Бренд: E-Z Trail Страницы: 8

Бренд: B&K Страницы: 10

Бренд: Raven Страницы: 48

Бренд: Pacific Страницы: 16

Бренд: TC Electronic Страницы: 67

Бренд: Tascam Страницы: 3

Бренд: TDR Страницы: 8

Бренд: VADDIO Страницы: 58

Бренд: mychway Страницы: 56

C-HB-A-LB2-SCCT Series

Бренд: C-LITE Страницы: 9

X-431 Torque HD

Бренд: Launch Страницы: 3

INTRAmatic 31 ES

Бренд: KaVo Страницы: 52

Бренд: Daavlin Страницы: 55

Бренд: Daavlin Страницы: 19

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды