Woods RB750-4 Скачать руководство пользователя страница 21

Страница: 21 / 54

Assembly

MAN0160 (Rev. 8/19/2005)

Models: MA, SA, & TA or Optional
Hydraulic Angle Kit 1004870

Install Hydraulic Angle Cylinder

Refer to Figure 7.

Remove lock pin assembly (2) and safety pin (10)

from rear of boom, if previously installed. See Figure
6 on page 20 for lock pin assembly location.

Remove hardware and retaining cap (3) from top

of boom if previously installed. See Figure 6 on page
20 for retaining cap location.

Place hydraulic angle arm assembly (4) on boom

as shown Figure 7.

Secure into position using three cap screws (27),

lock washers (25), and flat washers (26).

Attach hydraulic cylinder (6) to boom and hydrau-

lic angle arm assembly as shown. Secure with pins
supplied with the cylinder.

Attach hose holder (5) to A-Frame using carriage

bolt (24), flat washer (23), and lock nut (22).

Install adjustable elbows (7) and hoses (8) (Mod-

els MA and TA) to cylinder.

NOTE:

Do not install 84” hoses (8) if Hydraulic Offset

cylinder is to be installed.

Route hoses as shown in Figure 8.

Hyd Angle Arm Assembly

Hyd Hose Holder

Hyd Cylinder 3-1/2 x 16

Elbow, 3/4 ORBM 3/4 JICM 90

Hose, 3/8 84 1/2 NPTM 3/4 JICF

Strap, Binding 14-1/2

22.

Nut, Lock 3/8

23.

Washer, Flat 3/8 Standard

24.

Bolt, Carriage 3/8 NC x 1-1/4 GR1

25.

Washer, Lock 3/4

26.

Washer, Flat 3/4 SAE

27.

Cap Screw, 3/4 NC x 3 GR5

Figure 7

Angle Kit Installation

Figure 8

Angle Kit Hose Routing

NOTE:

For model

, Proceed to page 24 for hydraulic offset cylinder and relief valve installa-

tion instructions.

23 22

CD5986

CD5998

Содержание RB750-4























































Результаты поиска

Содержание RB750-4

Отзывы:

Похожие инструкции для RB750-4

Бренды по названию

Популярные бренды

Woods RB750-4, Руководство оператора

Результаты поиска

Содержание RB750-4

Отзывы:

Похожие инструкции для RB750-4

Бренды по названию

Популярные бренды