22
Assembly
MAN1255 (3/19/2018)
1.
Attach rubber deflector (1) and link (2) to front of cutter using carriage
bolts (3) and flange lock nuts (4).
2.
Insert bolts from inside the cutter frame out through the shielding.
FILL GEARBOX
NOTICE
■
Gearbox is not filled at the factory. Prior to delivery to customer,
make sure gearbox is filled only half-full with 80W or 90W API GL-4 or
GL-5 gear lube. Use side hole to remove any excess oil.
1.
Remove vent plug/dipperstick (9) on top of gearbox and plug on side of
gearbox. Use 5/16" allen wrench to remove plug.
2.
Make sure vent plug hole is clear.
3.
Fill gearbox until oil runs out the side hole on gearbox. Use a high quality
gear oil with a viscosity index of 80W or 90W and an API service rating of
GL-4 or GL-5.
4.
Install side plug and vent plug.
DUAL TAILWHEEL INSTALLATION BB720XE & BB840XE
(OPTIONAL)
1.
Attach dual tailwheel (1) to main frame (2) using position 5B and desired
height location as shown in Figure 33.
2.
Secure with cap screws (3) and hex nuts (4).
3.
Torque hardware to 237.3 N-m (175 lbs-ft).
Figure 33
. Dual Tailwheel Installation
CHECK CHAIN INSTALLATION (OPTIONAL)
Check chains are used to carry the front of cutter at a set height. See Figure
34.
1.
Thread check chains (3) through check chain bracket (2).
2.
Attach lower end of check chain (3) to mast plate with bolt (6), washer
(7), and nut (8).
3.
Attach keyhole brackets (2) to each side of tractor top link bracket with
bolt (4) and nut (5).
Figure 34
.
Optional Check Chain Assembly
RELOCATE BAFFLE
NOTE:
Baffle may need to be relocated to the front of the cutter to prevent
excessive blow-out when cutter is used on a non-cab tractor.
1.
Remove the rear baffle and hardware.
2.
Replace the two 3/8" carriage bolts that were removed from each side of
the rear frame. Torque to 47.5 N-m (35 lbs-ft.).
3.
Turn the baffle 180-degrees. Secure to the inside of the two mounting
brackets with carriage bolts (2) and lock nuts (3) that were previously
removed.
4.
Secure baffle to the brackets attached to each of the side frames with 3/8
self-tapping screws (1).
5.
Tighten all hardware 47.5 N-m (35 lbs-ft.).
Figure 35
.
Baffle Installation
1. Dual tailwheel
2. Deck, BB720XE &
BB840XE
3. 5/8 NC x 2-1/2 HHCS
4. 5/8 Flange lock nut
2. Check chain bracket
3. 3/8 Chain, 32-link
4. 3/4 NC x 6 HHCS GR5
5. 3/4 NC Lock nut
6. 5/8 NC x 2-1/4 HHCS GR5
7. 5/8 Flat washer
8. 5/8 NC Hex nut
1. 3/8 NC x 1 Self-tapping screw
2. 3/8 NC x 1 Carriage bolt
3. 3/8 NC Flange lock nut
Содержание BRUSHBULL BB600XE
