background image

4

LT 90 Owners Manual

2015

Safety

Fuel

• Never shut power off to the LT90 if there is a fire and fuel in the firebox unless 

there is an emergency.

• Take the proper precautions to ensure that the modifications made to an existing heating system does not

 

interfere with existing safety controls. 

• Never use the following: trash, plastics, gasoline, rubber, or naphtha in your WoodMaster LT 90.
• Read and follow these directions carefully. Retain this manual for as long as you own your LT 90.

Sweeping

The chimney should be inspected and cleaned as needed, typically twice a year. This is to be done by qualified 

persons. Shut off the furnace, disconnect power and allow the system to cool before attempting to clean the 

system.

Warning!

Always disconnect the power to the furnace before any cleaning or maintenance. Service agreements increas

-

es operation length and life of the unit. For more information contact your local WoodMaster dealer.

Replacement parts should only be genuine Northwest Manufacturing, Inc. components. Your dealer can supply 

the genuine service parts and install them. 

All fuels must conform to certain quality standards to ensure trouble free operation of the furnace. Use 

of unapproved fuels may result in faulty operation and a voided warranty. Never use the following: trash, 

household garbage, plastics, gasoline, rubber, naphtha, leaves, and materials treated with petroleum prod

-

ucts (ie: particleboard, railroad ties & pressure treated wood). Newspaper and plain, unprinted cardboard 

should only be used as kindling, not as fuel. Other paper products should not be used.  Please contact your 

WoodMaster dealer for any questions on fuel use.

Only cut, split, seasoned wood with a internal moisture content of 25% or less may be used. Wood can be cut 

to a maximum length of 27 inches. The wood should always be placed horizontally and parallel to the firebox 

wall. The pieces of wood should be stacked as tightly as possible whereby the face of the wood should NOT 

touch the firebox wall. This ensures proper air flow. DO NOT burn any large, round pieces of wood. DO NOT 

burn any “green wood”, or any wood that is above the 25% moisture limit.

Water Content

The maximum permitted water content is 25%.

Bark Content

The maximum permitted bark content is 20%.

Содержание LT 90

































Отзывы: