Wood master LT 90 Скачать руководство пользователя страница 25

Страница: 25 / 32

LT 90 Owners Manual

2015

Warranty

This Warranty is provided by Northwest Manufacturing, Inc. only for the benefit of the initial purchaser (Original Owner) of the

Northwest Manufacturing, Inc. LT 90 (the “Furnace”) on the original site of installation (the “Site of Original Installation”). This

Warranty provides specific legal rights. You may have other rights depending on where you live.

The rights in this warranty depend on the proper assembly, installation and commissioning of the Furnace by a dealer or installer

who is certified by Northwest Manufacturing, Inc. (the “Certified Contractor”); and proper operation and maintenance. Proper

maintenance in accordance with the Maintenance Intervals (as defined herein) must be preformed. Installation by an uncertified or

unqualified contractor or installer and/or improper maintenance, operation, misuse or abuse of the Burner shall void this Warranty

in whole or in part.

LIMITED FIVE (5) YEAR WARRANTY FOR THE FIREBOX AND WATER JACKET

Northwest Manufacturing, Inc. warrants that the Firebox and Water Jacket of the Furnace shall be free of defects in material and

workmanship for FIVE (5) YEARS from the Date of Original Installation. If there is a leak in your properly delivered and installed

WoodMaster LT 90 in the first year, WoodMaster will replace the furnace at no cost to the original owner. (A leak means; a leak in

the firebox or water jacket.) Northwest Manufacturing, Inc. will only pay costs of warranty work for years two (2) through five (5)

– 100% of warranty work, once a defect is determined, repair or replacement of the Firebox and Water Jacket, in a whole or part,

will be at the sole discretion of Northwest Manufacturing, Inc..

LIMITED ONE (1) YEAR WARRANTY ON ELECTRICAL COMPONENTS

Northwest Manufacturing, Inc. warrants to the Original Owner, electrical components are free from defects for the period of one (1)

year from the date of installation. Northwest Manufacturing, Inc. will determine whether to repair or replace the defective parts.

LIMITED ONE (1) YEAR WARRANTY ON ADDITIONAL COMPONENTS

Northwest Manufacturing, Inc. warrants to the original owner only, any additional components, including, but not limited to the

outer shell, paint, insulation, doors and latches during normal usage for a period of one (1) years from the date of installation.

START OF WARRANTY PERIODS

The Warranty Period shall begin on the date the Furnace installation has been completed (the “Original Date of Installation”). In the

event of dispute as to the Date of Original Installation, the shipping date of your Furnace, as recorded by Northwest Manufactur-

ing, Inc., shall be deemed to be the Date of Original Installation.

WARRANTY LIMITATIONS

I. Damages for unsatisfactory performance caused by improper installation or any damages caused by or as a result of improper

use of the Furnace, incorrect start-up, incorrect or careless handling, improper control adjustment, disregard of the operating

instructions and proper maintenance or disregard of any other instructions supplied with the Furnace, improper operation of the

Furnace or improper alteration and repairs/service by a third party not affiliated with Northwest Manufacturing, Inc. will not be

covered under this warranty. Damage due to water freezing will not be covered. All repairs must be performed by a Certified

Contractor. The warranty does not cover replacing water, antifreeze, or boiler treatment.

II. The warranty will not cover damage to parts caused by improper installation, improper care or maintenance. The Furnace, and

any installed accessories must be serviced, inspected and cleaned at regular intervals. Northwest Manufacturing, Inc. will NOT

warranty damage to the Furnace due to ash corrosion.

III. The workmanship, repairs or replacement of parts of the Certified Contractor will not be covered under this warranty.

IV. Components of the heating system not furnished by Northwest Manufacturing, Inc. as part of the Furnace are not covered under

this Warranty. Damages caused by components of the heating system not supplied by Northwest Manufacturing, Inc. will not be

covered under this Warranty.

V. Fuels used in the Burner must meet the specifications set out by Northwest Manufacturing, Inc.. Suitable fuels are listed in the

owners manual. Damage caused by the use of any unapproved fuel, or any fuel that does not meet the guidelines set forth by

Northwest Manufacturing, Inc. will not be covered by this warranty.

FIVE (5) YEAR LIMITED WARRANTY - FIREBOX & WATER JACKET

Содержание LT 90

































Результаты поиска

Содержание LT 90

Отзывы:

Похожие инструкции для LT 90

Бренды по названию

Популярные бренды

Wood master LT 90, Руководство пользователя

Результаты поиска

Содержание LT 90

Отзывы:

Похожие инструкции для LT 90

Бренды по названию

Популярные бренды