Wolf Compact plus 32 E, Инструкция по эксплуатации

Страница: 14 / 37

14
G
Maintenance
1
Attention! Rotary cutter blade
Before all maintenance and cleaning work:
z
Pull out the power plug.
z
Do not touch running blades.
z
Never spray down the lawnmower using water, especially not
at high pressure.
z
Regularly check and tighten all visible screws and nuts, espe-
cially those relating to the cutting bar, to ensure a firm fit.
z
Always have blades changed or re-sharpened by a specialist
workshop, since a balance test must be carried out as speci-
fied in the safety regulations following any removal of parts.
z
Only use original WOLF spare parts. Otherwise we can’t gua-
rantee that your mower conforms to the safety regulations.
z
Never park your lawnmower in damp rooms.
z
For safety reasons, replace worn or damaged parts.
Disposal
Assembly
Fasten handle bars
1
Caution!
The cable can be damaged while folding up or pulling out
the handle bar.
z
Inlay the cable in the bend protection .
z
When adjusting the handle height take care that the ca-
ble is not crimped
1. Fold the bottom part of the handle up and screw it tight with
the two hand wheels .
2. Set the handle to the desired height .
3. Fold the upper part of the handle out and screw it tight with the
wing nuts .
Mount the collecting bag
1. Place the chute (1) on the collecting bag flap (2) .
2. Press the chute from behind onto the collecting bag flap. The
chute is ready for use as soon as it locks into place .
Operation
General
Operating times
z
Please check noise abatement regulations prevailing in your
country.
Feed cable through the strain relief
z
Please feed cable through the strain relief .
3
Note: WOLF Flick-Flack®
WOLF Flick-Flack® keeps the cable away from the cutting
unit .
Set cut height
1
Attention! Rotary cutter blade
Undertake work/adjustments on the equipment only after
the motor is switched off and the cutting tool has come to a
standstill.
z
Switch off motor and pull out power plug.
1. Pull the lever out .
2. Set the desired cutting height .
3. Press the lever back in .
Selection of Cutting height
z
If possible, mow when grass is dry in order to protect turf. Do
not se cutting position too low when mowing very hight or wet
grass.
z
We recommend an average cutting height of 40 mm.
Connecting to the mains (230 Volts, A.C., 50 Hz)
z
The mower operates from any normal household mains supp-
ly, provided with a 16 Amps. fuse.
3
Note: Residual current protection device
These protection devices safeguard while touching
damaged wires, from insulation flaws and in certain cases,
also while damaging live wires.
z
We recommend that the equipment only be plugged into
a power socket, which is protected by a residual current
protection device (RCD) with a residual current of not
more than 30 mA.
z
Retrofit kits are available for old installations. Consult an
electrician.
Starting and Stoping
z
Switch on motor with mowerplaced on level and firm ground.
z
not in high grass - alternatively tilt slightly .
Switch-on motor
1. Depress button and hold (1).
2. Lift up bar (2).
3. Release bar (2).
Switch-off motor
z
Release bar (2).
Tips for mowing
z
To prevent strips of grass from being left unmowed, the cutting
paths must always overlap a few centimeters
.
z
Always let cable trail on the cut side of the lawn.
Do not dispose of electrical equipment in domestic
waste. Recycle equipment, accessories and pa-
ckaging in an environment-friendly manner.
A B C D
A
C
B
C
D
E F G
E F
G
H
H
J
K
L
M
N
O
O
P