Wohler iVAM1-12G Скачать руководство пользователя страница 114 | Manualshive

Страница: 114 / 125

Wohler iVAM1-12G Скачать руководство пользователя страница 114

iVAM1-12G

Page 114

ZMAN Session Sources

If the ZMAN card is to Source Flows, use the

Session Sources

tab. Refer to Figure

D-8. The procedure is similar to defining Sinks with the additional step to provide
the Flow a name to appear on other units in the network. Select the channel range
with a maximum of 8 channels per Flow.

Figure D-8: Session Sources Tab

ZMAN Updating

The Zman card is pre-initialized with the correct Wohler firmware load. In case of
future upgrades, use the following steps:

1.

In Aneman, right click the ZMAN entry on the bottom Devices section, and
select Maintenance Mode. This brings up a web page which prompts for the
location of the Wohler provided upgrade file. The file should resemble the
following:

firmware_1.1.7b43263_18Jun20.wohler

2.

Select this file and click Open. On the web, select Update to install the
firmware.

3.

After successful completion, select Reboot to reboot the ZMAN card.

4.

Close the web pages and return to Aneman to set up Sources and Sinks.

«
...
112
113
114
115
116
...
»

Содержание iVAM1-12G






























































































































Отзывы:

Нет отзывов