Wohler iVAM1-12G Скачать руководство пользователя страница 100 | Manualshive

Страница: 100 / 125

Wohler iVAM1-12G Скачать руководство пользователя страница 100

iVAM1-12G

Page 100

AES67

The iVAM1-12G Brooklyn II can be configured for AES67 operation. AES67
operation with Dante is limited to eight or less receive and transmit channels at 48
kHz sample rates.

24 bit linear (L24) encoding and 1 msec packet time are fixed default transmit
parameters.

16 bit (L16) or 24 bit (L24) encoding and 125/250/333/100 µsec packet times can
be received.

The

Device View - AES67 Config

menu enables/disables AES67.

Figure B–5: AES67 Enable/Disable

Further, Dante AES67 discovery and operational protocol requires manual
assignments for static multicast transmit and receive IP addresses per Dante
protocols for discovery and IGMP network operation. Destination addresses in range
239.nnn.0.0 – 239.nnn.255.255, port 5004 o nnn can be configured using the
Dante Controller. The default is 69. The destination and receive address range must
match. Provisions for this are in

Dante Controller Device View - Network

Config

. Refer to Figure B-6.

«
...
98
99
100
101
102
...
»

Содержание iVAM1-12G






























































































































Отзывы:

Нет отзывов