background image

5

Additional camera registration

In the <

Install Wizard

> setting, make a connection to the camera automatically registered and use the menu 

path to register and connect a camera.

Menu 

;

 Device 

;

 Camera 

;

 Cam Registration 

;

 Auto

a

b

c

e

d

To register a camera, follow these steps:

a

  Select the camera to register (you can select multiple cameras).

b

   Click the <

ID

> and <

P/W

> window to enter <

ID

> and <

P/W

> of the selected network camera. (If you do 

not register a new ID/PW, then the default ID/PW combination is used.)

c

  Click <

Connection Test

>.

d

  Check the connection results. 

e

  If the channel connected successfully, click <

Register

> to end the camera registration process.

 

M

 

`

Click an item on the table to see a preview (you must change the ID and Password in step “

b

” if the camera account 

changes).

 

`

Click the table headers to sort the content.

 

`

Click < 

 > to check if a new IP address was allocated to the camera when you rescan the network or when an IP 

address was not assigned by the DHCP server (e.g., 192.168.1.100). If the IP still stays the same, then select Assign IP to 

assign the IP manually.

Configuring the Recording

This section outlines how to configure and view the recording settings for each channel.

a

b

c

FULL

NO

   SCSI

Recording Restriction

Record data size exceeded limitation

Only key frames are recorded

Please check the record settings

Do not show this message again

OK

Record Status

d

a

  Shows the standard and event recording method for each channel.

 

• FULL : Records all the frames received from the camera.

 

• KEY : Records only the key frames received from the camera. In general, one or two frames per second 

are recorded, but you can adjust this in the camera settings.

 

• OFF : Turns off recording.

b

  Shows the transmission size of the recording data for each channel. 

c

  Shows the data size limit for each channel.

 

M

 

`

The orange colored channel indicates the case where the 

b

 input data load is greater than the 

c

 permitted data load.  

If you set the 

c

 permitted data load to greater than the 

b

 input data loads, it will be changed to orange.

 

`

If the sum of input data for each channel is greater than the max level for the camera, then 

d

 the recording exceeding icon 

and the alarm message will be displayed. In this case, for the channel exceeding the input limit will record the main 

frame(one or two per second) only.

Содержание XRN-1610












Отзывы: