Wireless Devices NetPage NP-14 Series Скачать руководство пользователя страница 14 | Manualshive

Страница: 14 / 32

background image

14

Description :

CheckSum = 662H (02H+30H+30H+30H+30H+31H+32H+38H+41H+31H

+31H+61H+62H+63H+64H+65H+66H+67H+68H+69H+6AH+6BH)

CCCC = 0662 (30H,36H,36H,32H)

Total contents = 02H + “0000128A11abcdefghijk0662” + 04H

EX3. Num. 512 bps 1000122

N51

xxx… 6A3C

Description : CheckSum = 126A3CH ( only use last 4 digits as valid ) CCCC = 6A3C

(36H,41H,33H,43H)

Transmitter send to PC

If command accept to transmitter then transmitter send CCCC +

ACK

(06H) to PC .

the CCCC is check sum of message.

if command did not accept to transmitter will not send back CCCC +

ACK

(06H) within

200 mS .

Note: Transmitter encoder message must be based on two conditions as below.

Then, it can encode all messages and send out all messages at one time.

1. PC send message then receive the ACK from transmitter and PC send first

byte of next message less than 150mS after last ACK.

2. Transmitter received total messages less then 15K bytes. Idle Capcode is

from 2007664 to 2007671.

«
...
12
13
14
15
16
...
»

Содержание NetPage NP-14 Series

































Отзывы:

Нет отзывов

Похожие инструкции для NetPage NP-14 Series

Бренд: Srne Страницы: 38

Бренд: SAJ Страницы: 26

Бренд: Lika Страницы: 2

Бренд: ICP DAS USA Страницы: 7

Бренд: Dolby Laboratories Страницы: 23

Al-Mu'allim AM-RD2

Бренд: PLAYNETICS Страницы: 21

Бренд: Linear Technology Страницы: 26

Бренд: Tripp Lite Страницы: 24

Бренд: Optical Systems Design Страницы: 20

Бренд: HQ Power Страницы: 8

CONVERTEON AT-CM201

Бренд: Allied Telesis Страницы: 3

Бренд: Telefunken Страницы: 34

Бренд: Blueant Страницы: 16

AM 3616/4096BG Series

Бренд: Lika Страницы: 36

Tascam LA-80MKII

Бренд: TEAC PROFESSIONAL Страницы: 16

Бренд: Violectric Страницы: 28

IE-MediaChassis/1

Бренд: IMC Networks Страницы: 12

Бренд: Planet Страницы: 28

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды