Wireless Devices NetPage NP-14 Series Скачать руководство пользователя страница 9 | Manualshive

Страница: 9 / 32

Wireless Devices NetPage NP-14 Series Скачать руководство пользователя страница 9

9

INSTALLATION

Introduction

This chapter provides basis information in installation help of the NP-14 Netpage

transmitter device.

Installation

Installing the NP-14 involves identifying the interface connections for communication

with the host equipment and connecting the module. The connector pin orientation is

shown in Figure 20 Corresponding signal name and color codes are listed in table

1-1.1-2.1-3.1-4.mount and connect the NP-14 as follows:

←

←

←

←

Figure 20. Main I/O of Rear view

Table 1-1.COM1,RS232 SERIAL PORTS (9 way female) PIN SIGNAL DIRECTION

DB9 - View looking into female
connector (NP-14 side)

1 N/C

2 RECEIVE DATA (RX) IN

3 TRANSMIT DATA (TX) OUT

4 N/C

5 GROUND (GND)

6 N/C

7 N/C

8 CLEAR TO SEND (CTS) IN

Link by RS-232

Plug the RS-232 Cable into an available DB9 serial port connector on the back of a Host Device, such

as a PC or Nurse Call system or other Host Device. If the serial port has a DB25 connector, you must

provide a DB25 to DB9 adapter, which is available from NP-14 or from a computer supply company.

Tighten the connector screws. Plug the RS-232 Cable into the DB9 female connector on the

Transmitter Unit. Tighten the connector screws again.

The RS-232 Cable is a parallel wire: Pin 5 to pin 5, Pin 2 to pin 2, Pin 3 to Pin 3.

«
...
7
8
9
10
11
...
»

Содержание NetPage NP-14 Series

































Отзывы:

Нет отзывов