Winterthur Gas & Diesel Ltd. X52 Скачать руководство пользователя страница 481 | Manualshive

Страница: 481 / 519

background image

•

Cat fines

Cat fines cause cylinder liners to become worn. Cat fines are attached to water droplets and
are very difficult to remove from the fuel. With correct treatment in the fuel separator, the
aluminum and silicon content of 60 ppm (mg/kg) can be decreased to 15 ppm (mg/kg), which
is thought to be satisfactory. For satisfactory separation, a fuel temperature as close as
possible to 98°C is recommended. A decreased fuel flow rate through the separator gives
a better separation. This is because the fuel stays in the separator for a longer period. Also
obey the instructions of the equipment manufacturer.

Cat fines can collect in the sediment of the fuel tank from other bunkers. During bad weather
conditions, the movement of the ship mixes the sediment into the fuel. Thus, it is better to
think that all fuels contain cat fines, although it is possible that a fuel analysis can show a
different result. Thus do also regular procedures to remove sludge and cat fines from the
fuel that is in the settling tank and the service tanks.

12.11.3.12 Used Lubricating Oil and Chemical Waste

Used lubricating oils and chemical waste must not be mixed into the fuel. If you do so, the fuel
would not be stable because the base oil is very paraffinic and can cause too much sludge. Most
used lubricating oil is from the crankcase, thus large quantities of calcium, zinc, phosphorous and
other additives and wear metals can cause contamination. The limits in ISO 8217:2017 and the
WinGD specifications make sure that no used lubricating oil is in the fuel.

Chemical waste (eg polymers, styrene and other chemical substances) must not be added to the
fuel. These materials can cause the fuel to become too thick, to become almost solid and thus can
cause blocked filters. They can also cause corrosive attacks and damage to the fuel injection
system.

12.11.4

Distillate Fuel Specifications

Since 2015 more frequently distillate fuels are used in 2-stroke engines to obey the new ECA rules.
Distillate fuels are easier to operate than residual fuel, but caution is necessary for some problems.

In ISO 8217:2017 there are specified the DMX, DMA, DMZ and DMB grades and the new DFA,
DFZ and DFB grades with a maximum fatty acid methyl ester (FAME) content of 7.0 volume %.
The WinGD specifications use the DMB grade which is the highest viscosity grade, refer to

12-13 - Specifications for distillate fuels

. The DMX grade is not applicable for use in 2-stroke

engines because of its low flash point and viscosity.

Tab 12-13 Specifications for distillate fuels

Parameter

Bunker limit

At engine inlet

Unit

Test method

Kinematic viscosity
at 40°C

Maximum 11.0

Minimum 2.0

Minimum 2.0 (not re-
lated to temperature)

mm

2

/s [cSt]

1

ISO 3104

Density at 15°C

Maximum 900

Maximum 900

kg/m

3

ISO 3675/12185

Cetane index

Minimum 35

Minimum 35

-

ISO 4264

Sulphur

2

Maximum 1.5

Maximum 1.5

mass %

ISO 8754/14596

Flash point

Minimum 60

Minimum 60

°C

ISO 2719

Hydrogen sulphide

3

Maximum 2.0

Maximum 2.0

mg/kg [ppm]

IP 570

X52

AA00-0000-00AAA-030A-A

Operation Manual

Diesel engine fuels

Winterthur Gas & Diesel Ltd.

- 481 -

Issue 002 2018-11

«
...
479
480
481
482
483
...
»

Содержание X52








































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для X52

Бренд: Ace Страницы: 17

Бренд: ACE INSTRUMENTS Страницы: 33

Бренд: ACE INSTRUMENTS Страницы: 2

Бренд: ACE INSTRUMENTS Страницы: 2

Бренд: TapFlo Страницы: 35

Бренд: DANA Страницы: 8

Бренд: 2E Страницы: 6

BTL PA0400 Series

Бренд: Balluff Страницы: 22

Micropulse BTL5 Series

Бренд: Balluff Страницы: 12

BNI IOW-560-W01-K022

Бренд: Balluff Страницы: 32

Бренд: Baltic Страницы: 68

Бренд: Baltic Страницы: 68

Max Charge MC-612

Бренд: Balmar Страницы: 12

BTL PA0400 Series

Бренд: Balluff Страницы: 204

Бренд: Hanna Instruments Страницы: 2

Бренд: Hanna Instruments Страницы: 2

Бренд: Hanna Страницы: 12

Бренд: Hanil Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды