WinGD X62DF-S2.0 Скачать руководство пользователя страница 83 | Manualshive

Страница: 83 / 259

background image

Marine Installation Manual

2022-03

4-4

4 Ancillary Systems

4.2 The iCER

X62DF-S2.0

4.2

The iCER

This engine is equipped with the Intelligent Control by Exhaust Recycling
(iCER) system. This facilitates the recirculation of part of the exhaust gas back to
the engine. By replacing some of the oxygen with CO

2

, the stability of the engine

combustion is increased. This allows for an increase in the engine pressure ratio
and a resulting increase in combustion efficiency.

This engine can also be selected with iCER operation in diesel Tier III mode
(see

iCER operating mode options,

). In this case, exhaust gas recirculation

is used to reduce the NO

x

emissions.

Figure 4

-

2 Overview of the components for the iCER system with one turbocharger

Exhaust Gas Cooler (EGC)
(pre- and main stage)

Circulation tank

Additional economiser
(optional)

Colour code

Grey: Delivered with the engine

Green/Blue: Piping system according to shipyard’s supply, including supports,

explosion relief devices where necessary, etc.

Purple: To be ordered from certified supplier

Yellow: Valves

Flow Regulating Valve (FRV)
(with shut off function)

Shut-Off Valve (SOV)

Back-Pressure
Valve (BPV)

Bellows, to separate
the engine from
the piping system

Water Mist Catcher (WMC)
(delivered with the engine)

Self-closing
explosion pressure
relief valve

Purging & Sealing Valve (PSV)
(development in progress;
details not yet available)

Bellow, to compensate the thermal
expansion
(amount and positions according
to project specific requirements)

SM-0828

«
...
81
82
83
84
85
...
»

Содержание X62DF-S2.0




































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для X62DF-S2.0

Бренд: NARGESA Страницы: 33

Бренд: Campden instruments Страницы: 8

Бренд: Taylor Made Страницы: 2

Бренд: York Fitness Страницы: 18

Бренд: Safco Страницы: 2

Бренд: Omni Страницы: 193

Бренд: Labnet Страницы: 2

WJHD309A - DIGITAL DISK RECORDER

Бренд: Panasonic Страницы: 79

Бренд: FEAS Страницы: 72

Бренд: Above All Страницы: 4

Бренд: OAKWORKS Страницы: 2

Бренд: Oakton Страницы: 2

Бренд: Oakton Страницы: 2

Бренд: O2matic Страницы: 4

Бренд: Qlight Страницы: 4

Chicken Coop Plan 3x5

Бренд: EASY COOPS Страницы: 21

Chicken Coop Plan 4x6

Бренд: EASY COOPS Страницы: 18

Chicken Coop Plan 8x10

Бренд: EASY COOPS Страницы: 18

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды