WinGD X62DF-S2.0 Скачать руководство пользователя страница 67 | Manualshive

Страница: 67 / 259

background image

Marine Installation Manual

2022-03

3-10

3 Engine Installation

3.5 Engine foundation and seating

X62DF-S2.0

3.5

Engine foundation and seating

3.5.1

Engine load and force transmission

The engine seating foundation is a structural part of the ship integrated into the
double-bottom structure. It must be designed to absorb static and dynamic
forces, vibrations and torques from the engine, shaft and the propeller.

Figure 3

-

4 Force transmission to the engine foundation

The propulsion thrust is transmitted along the propulsion chain to the engine
structure through the thrust bearing. Thrust sleeves are required to absorb the
thrust force. In addition, the dynamic behaviour of engine forces requires a stiff
engine seating foundation (see the standard bolting in

).

3.5.2

Engine foundation layouts

Depending on the owner’s requirements and on the ship design, a standard or a
narrow engine foundation layout are possible for the engine seating foundation.
The main difference between the two engine foundation layouts is the width of
the lube oil drain tank underneath the engine (see

).

Figure 3

-

5 A comparison of the standard and narrow engine foundation layout

SM-0824

Thrust

bearing

SM-0825

Longitudinal

s

Ɵī

eners

Lube oil drain tank

Lube oil drain tank

Rib

Rib

Standard engine founda

Ɵ

on layout*

Narrow engine founda

Ɵ

on layout*

(*Design a

Ʃ

ributes with di

ī

erences are marked with colour)

Side girder

Side girder

Double-wall

structure

Co

ī

erdam

«
...
65
66
67
68
69
...
»

Содержание X62DF-S2.0




































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для X62DF-S2.0

Бренд: GE Страницы: 802

Бренд: iET Страницы: 17

Бренд: 3M Страницы: 2

Бренд: NARGESA Страницы: 50

DVCPRO P2 Series

Бренд: Panasonic Страницы: 32

Бренд: Facsimile Страницы: 16

Growers Supply 109722

Бренд: FarmTek Страницы: 9

Бренд: Gardena Страницы: 19

Бренд: Jackco Страницы: 6

Бренд: EuroLite Страницы: 28

Бренд: Macht Dental Страницы: 8

Бренд: Naked Страницы: 36

Бренд: U-Line Страницы: 9

Green Machine H-3518

Бренд: U-Line Страницы: 3

Бренд: Zimmer Страницы: 54

Бренд: Zimmer Страницы: 4

Бренд: Zimmer Biomet Страницы: 23

Бренд: Zimmer Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды