Winegard WB-2000 Скачать руководство пользователя

Страница: 38 / 39

Appendix B. Recommended Receivers

Winegard recommends the following receivers for use with your Winegard Automatic

Satellite System. Winegard does not recommend the use of receivers with hard drives for

mobile use. All information below is accurate as of March, 2007. Receivers and

compatibility is subject to change without notice.

Service Provider

Standard Receiver

HD Receiver

DirecTV

D10, D11

H10, H20

Dish Network

311, 301

VIP 211

Bell ExpressVU

3100

4100

Appendix C. Normal Operating Messages

The Winegard Satellite Interface LCD screen keeps the user informed as to what the dish is

doing through simple messages. Below is a short table of messages that are displayed dur-

ing normal operation.

The LCD screen will also give feedback when an error has occurred either in the antenna or

in communication with the antenna.

Message

Dish Status

To Clear

SLEEP

MODE

Stationary Units: Target satellite has been

acquired

In-Motion Units: Target satellite has been

acquired & vehicle exited Tracking Mode

to sleep Mode

Press

[ENTER]

to clear manually and

return to status screen, or wait 1 minute to

automatically clear

HOMING

ELEVATION

Antenna is searching for the elevation limit

switch

Will clear when antenna sets elevation

home position

HOMING

AZIMUTH

Antenna is searching for the azimuth limit

switch

Will clear when antenna sets azimuth home

position

SEARCHING

Antenna is searching for the target satellite Will clear when target satellite has been

identified

connecting to

antenna

Interface is powering up & interface &

antenna are establishling communications

Will clear within 30 seconds of power up

under normal operation

Содержание WB-2000








































Результаты поиска

Содержание WB-2000

Отзывы:

Похожие инструкции для WB-2000

Бренды по названию

Популярные бренды

Winegard WB-2000, Руководство по установке и эксплуатации

Результаты поиска

Содержание WB-2000

Отзывы:

Похожие инструкции для WB-2000

Бренды по названию

Популярные бренды