background image

2000000501 (Rev. B - 04/23)

HTHBSM-1A,  HTHBSM-2A,  HTHBSMWF-1A,  HTHBSMWF-2A

Page 1

Installation & Use Manual

HydroBoost

®

 Surface Mount Bottle Filling Station

Warnings

1. Use with clean, clear, fresh potable drinking water only!  Do not use with water that is microbiologically 

unsafe or of unknown quality without adequate disinfection before the system.

2. Connect Power Cord only to a grounded three prong electrical outlet with electrical power that:

a.  MUST be rated for this product as specified on product data label.

b.  MUST have over-current protection (e.g. Fuse, Breaker).

c.  MUST have Ground Fault Circuit Interrupt protection (GFCI).

d. 

These products are designed to operate on 20 to 105 PSI supply line pressure. If inlet pressure is

  above 105 PSI, a pressure regulator must be installed in supply line.  Any damage caused 

     by reason of connecting this product to supply line pressure lower than 20 PSI or higher than

     105 PSI is not covered by warranty

.

IMPORTANT

THIS IS AN INDOOR APPLICATION ONLY!

ALL SERVICE TO BE PERFORMED BY AN 

AUTHORIZED SERVICE PERSONNEL.

TOOLS/ITEMS REQUIRED

BUT NOT SUPPLIED

- SERVICE STOP VALVE WITH 3/8"

   COMPRESSION OUTLET

- FASTENERS FOR WALL TYPE (8 REQ’D.) 

- SLIP JOINT DRAIN UNION OR

   

COMPRESSION CLAMP

- 5/32" HEX-WRENCH

Model

HTHB-WF

To assure you install this model easily and correctly, PLEASE READ THESE 

SIMPLE INSTRUCTIONS BEFORE STARTING THE INSTALLATION. CHECK 

YOUR INSTALLATION FOR COMPLIANCE  WITH ALL PLUMBING, ELECTRICAL 

AND OTHER APPLICABLE CODES. FOLLOW ALL WARNINGS AND CAUTIONS 

CAREFULLY.  After installation, leave these instructions with the customer for future 

reference.

Installer

WARNING:

 Cancer and Reproductive Harm - www.P65Warnings.ca.gov

ADVERTENCIA:

 Cáncer y daño reproductivo - www.P65Warnings.ca.gov

AVERTISSEMENT:

 Cancer et effets néfastes sur la reproduction - 

www.P65Warnings.ca.gov

Patent zurn-elkay.com/patents

Содержание HydroBoost HTHBSM-1A








Отзывы: