background image

3

1. IDU Reset

A) Power on IDU by pressing and holding the Power 

button for 3 seconds, then press and hold ENTER to 
enter the user menu.

B) Once “Enter User Menu” appears, press SELECT to 

move the asterisk to “Yes” and press enter. 

C) Press SELECT twice until “Installation” is on the top 

line with an asterisk and press ENTER. 

D) You will be prompted to enter the password. Press 

ENTER four times. 

E) Press SELECT once until “Raise Antenna” is on the 

top line with an asterisk and press ENTER. 

F) Press SELECT to the move the asterisk to “Yes” and 

press ENTER.  

G) Once the antenna has raised, you will receive a 

“Raise Antenna - Raised” message. Press ENTER 
and repeat the “Raise Antenna” process until 
you receive the “Raise Antenna - Motor Stalled” 
message. 

(H) Power off IDU by pressing and holding POWER and 

SELECT simultaneously. If done correctly you will 
receive a “Powering Off Thank You” message. 

I) Please unplug the 6-wire data 

cable by pressing down the 
locking tab and gently pulling 
the cable out of the “DC OUT/
ANT. COMM.”.

    Now remove the DC power cord 

from the “DC IN” terminal.

Содержание TRAV'LER SK-73UP













Отзывы: