8
Features
Miter Cutting Head
The
miter cutting head
is the unit that cuts the
material and consists of a cast iron base, blade
support unit and guard, transmission unit, and
motor. The depth of cut is set by adjusting the
depth cut stop
. The miter cutting head swivels
and locks into -45º, 90º, and +45º by means of a
locking mechanism
. Depressing the mechanism
overrides the lock, permitting the head to adjust
to
any
position between -45º and +45
q
.
Miter Position Lock
The
miter position lock
secures the miter cutting
head from movement. The miter is secured
when the lock is pushed all the way to the left
and can be positioned when the lock is moved to
the right.
Self-centering Vise
The
self-centering vise
holds the work piece in
place during cutting. The work piece is secured
in the vise by turning the
vise handles
.
FK350 Controls
The
control panel
consists of the
Power
(On/Off)
switch and
High/Stop/Low
switch, and an
integral coolant system. To operate the
machine, the
Power
switch must be set to
on
and the
High/Stop/Low
switch must be set for
Hi
or
Low
. Then depress the trigger handle to start.
FK350-SX Controls
This machine features a 2-speed motor, feed
speed control, an integral coolant system, and
two modes of operation; manual mode, and
semi-automatic mode. In semi-auto, the
complete cut cycle is initiated via push button.
The semi-auto cut cycle closes the vise
clamping the material, powers the head down
completing the cut, then raises the head, and
opens the vise. In manual mode, head up/down,
and vise open/close is initiated by switches.
Trigger Handle
The
trigger handle
(Figure 1) is located on the
operating lever
used to raise and lower the saw.
It contains a
micro-switch
, which is activated
when the operator depresses the
run trigger
.
Figure 1
Flood Coolant System
The coolant pump must be
submerged before operating to prevent
damage to the pump.
Coolant is dispensed directed onto the saw
blade from a coolant fitting on the upper blade
guard. Coolant is provided through tubing from
the coolant pump (Figure 2) in the machine
base.
Adjust the coolant flow valve on coolant fitting to
achieve desired flow. When the coolant switch is
in the ON position, flow starts when the drive
motor is started. Turning off the coolant switch
stops coolant flow.
This coolant system can operate with either a
soluble oil base coolant or water-soluble
synthetic coolant. Coolant should be changed
regularly. Some recommended brands are
DoAll
and
Lenox
. These coolants are available at your
local industrial distributor.
Figure 2
Содержание -SX
