background image

2

Warranty and Service 

WMH Tool Group, Inc., warrants every product it sells. If one of our tools needs service or repair, one of our 
Authorized Service Centers located throughout the United States can give you quick service. In most cases, any of 
these WMH Tool Group Authorized Service Centers can authorize warranty repair, assist you in obtaining parts, or 
perform routine maintenance and major repair on your WILTON

®

tools. For the name of an Authorized Service Center 

in your area call 1-800-274-6848. 

MORE INFORMATION 

Group distributor, or visit wiltontool.com. 

WARRANTY 

WILTON products carry a limited warranty which varies in duration based upon the product. 

(MW = Metalworking)

WHAT IS COVERED? 

This warranty covers any defects in workmanship or materials subject to the exceptions stated below. Cutting tools, 
abrasives and other consumables are excluded from warranty coverage. 

WHO IS COVERED? 

This warranty covers only the initial purchaser of the product. 

WHAT IS THE PERIOD OF COVERAGE? 

The general WILTON warranty lasts for the time period specified in the product literature of each product. 

WHAT IS NOT COVERED? 

This warranty does not cover defects due directly or indirectly to misuse, abuse, negligence or accidents, normal 
wear-and-tear, improper repair or alterations, or lack of maintenance. 

HOW TO GET SERVICE 

The product or part must be returned for examination, postage prepaid, to a location designated by us. For the name 
of the location nearest you, please call 1-800-274-6848. 

You must provide proof of initial purchase date and an explanation of the complaint must accompany the 
merchandise. If our inspection discloses a defect, we will repair or replace the product, or refund the purchase price, 
at our option. 

We will return the repaired product or replacement at our expense unless it is determined by us that there is no 
defect, or that the defect resulted from causes not within the scope of our warranty in which case we will, at your 
direction, dispose of or return the product. In the event you choose to have the product returned, you will be 
responsible for the handling and shipping costs of the return. 

HOW STATE LAW APPLIES 

This warranty gives you specific legal rights; you may also have other rights which vary from state to state. 

LIMITATIONS ON THIS WARRANTY 

WMH TOOL GROUP LIMITS ALL IMPLIED WARRANTIES TO THE PERIOD OF THE LIMITED WARRANTY FOR 
EACH PRODUCT. EXCEPT AS STATED HEREIN, ANY IMPLIED WARRANTIES OR MERCHANTABILITY AND 
FITNESS ARE EXCLUDED. SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG THE IMPLIED 
WARRANTY LASTS, SO THE ABOVE LIMITATION MAY NOT APPLY TO YOU. 

WMH TOOL GROUP SHALL IN NO EVENT BE LIABLE FOR DEATH, INJURIES TO PERSONS OR PROPERTY, 
OR FOR INCIDENTAL, CONTINGENT, SPECIAL, OR CONSEQUENTIAL DAMAGES ARISING FROM THE USE 
OF OUR PRODUCTS. SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR 
CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU. 

WMH Tool Group sells through distributors only. The specifications in WMH catalogs are given as general information and are not
binding. Members of WMH Tool Group reserve the right to effect at any time, without prior notice, those alterations to parts, fittings, 
and accessory equipment which they may deem necessary for any reason whatsoever. 

Содержание -SX













































Отзывы: