background image

12

Miter Adjustment 

The adjust the miter position follow the steps 
below while referring to Figure 10: 

1.  Move the miter position lock (A) to the right 

to release. 

2.  Adjust the head to the desired angle ranging 

from –45º to +45º by pushing on the back of 
the motor to the right or left. The miter 
position is shown on the scale (B). 

3.  A detent mechanism locks the head in 

the -45º, 90º and +45º positions and will 
prevent the head from rotating. For a miter 
position other than -45º, 90º and +45º, press 
the lever (C) to release while rotating the 
head.

4.  When the desired cutting angle is set, move 

miter position lock

 (A) to the left to secure. 

Figure 10 

Trip Adjustment – FX350-SX 

The

height of retract

 and 

depth of cut trips

 set 

the travel limit of the head. 

Te set the trips (refer to Figure 11): 

1.  Turn the machine on and run in manual 

mode.

2.  Move the head up to the desired height of 

retract position. 

3.  Loosen the lock knob (A) and slide the trip 

(B) down until it makes contact with the trip 
plate (C).

4.  The trip plate fixes the position mechanically 

while the limit switch (D) signals the control 
system. 

5.  Tighten the lock knob. 

6.  Move the head down to the desired depth of 

cut position. 

7. Loosen 

the 

lock knob

 (E) and slide the 

trip

(E)

up

 until it makes contact with the 

trip

plate

(not visible in Figure 11). 

8.  Tighten the lock knob. 

Figure 11 

Depth Stop – FK350 

The

depth cut stop 

adjustment limits the lower 

travel limit of the saw blade during a cutting 
operation.

Remove power when 
making this adjustment. 

Failure to comply may result in serious 
injury!

To adjust the depth of cut (refer to Figure 12): 

1.  Using two 13mm wrenches, loosen the lock 

nut (A). 

2.  With the saw in the fully lowered position, 

turn the screw (B) until the saw blade 
bottoms out at the desired level. 

3.  Tighten the lock nut. 

Figure 12 

Содержание -SX













































Отзывы: