manualshive.com logo in svg

WilTec 61956, Руководство по эксплуатации, Страница: 14 / 16

Поделиться
Скачать
WilTec 61956 Скачать руководство пользователя страница 14

 

© by WilTec Wildanger Technik GmbH 

 

Item 61956

 

Page 14 

 

http://www.WilTec.de

 

http://www.aoyue.eu  

 

  

 

12 2021

-1

 

http://www.teichtip.de

 

 

Storage

 

 

Warning: 

Non-compliance with these steps might lead to residues in the carburettor leading to serious

 

starting problems or lasting damages after storing.

 

 

1.

 

Carry out all general maintenance work recommended in the “maintenance” section of the op-
erating manual.

 

2.

 

Clean the outer surface of the device.

 

3.

 

Empty the fuel out of the fuel tank.

 

4.

 

Start the motor after the fuel has been emptied.

 

5.

 

Let the motor run with idle-speed until the fuel remaining is consumed.

 

6.

 

Let the motor cool down (approx. 5

 

min).

 

7.

 

Use a spark plug wrench to remove the spark plug.

 

8.

 

Add 1 teaspoon of clean 2-stroke oil into the combustion chamber. Pull the starter rope several 
times slowly to lubricate the inner components. Re-place the spark plug.

 

9.

 

Store the device in a cool, dry play, away from ignition sources such as oil burner, water heater, 
etc.

 

 
 

Returning the device from storage

 

 

1.

 

Remove the spark plug.

 

2.

 

Pull the starter rope quickly to remove the excess oil from the combustion chamber.

 

3.

 

Clean the spark plug slot or install a new spark plug with an according slot.

 

4.

 

Prepare the device before use.

 

5.

 

Fill the fuel tank with the right fuel-oil mix (see “fuel and oil” section).

 

 
 

Troubleshooting

 

 

Problem

 

Possible cause

 

Possible solutions

 

Device  does  not  start  or  starts, 
but does not work.

 

Wrong starting procedure

 

Follow  instructions  in  operating 
manual.

 

Wrong carburettor mix

 

Have carburettor adjusted by au-
thorised technician.

 

Dirty spark plug

 

Clean slot or replace spark plug.

 

Empty fuel tank

 

Fill fuel tank with properly mixed 
fuel.

 

Primer pump pushed too often

 

Push  primer  pump  10

 

times 

slowly.

 

Device starts, but motor has low 
output.

 

Fuel filter clogged

 

Replace fireguards.

 

Wrong lever position

 

Put lever in “run” position.

 

Dirty fireguards

 

Replace fireguards.

 

Dirty air filter

 

Remove, clean, re-place filter.

 

Wrong carburettor mix

 

Have carburettor adjusted by au-
thorised technician.

 

Motor does not start

 

Wrong carburettor mix

 

Have carburettor adjusted by au-
thorised technician.

 

Clogged air filter

 

Clean or replace air filter.

 

No  electricity  supply  under  bur-
den

 

Old or wrongly mixed fuel

 

Empty  fuel  tank  and  fill  it  with 
fresh fuel.

 

Содержание 61956

















Отзывы:

Нет отзывов