Wilson Electronics 4G LTE 700 Скачать руководство пользователя страница 20

4G LTE 700 Specifications

4G LTE 700 Specifications

Model Number

271865

Antenna connectors

N-Female

Antenna impedance

50 ohms

Dimensions

5 .7 x 4 .2 x 1 .5 inch (14 .0 x 10 .8 x 3 .9 cm)

Weight

1 .27 lbs (0 .544 kg)

Frequency

Uplink 776 - 787 MHz / Downlink 746 - 757 MHz

1

Passband Gain (nominal)

Uplink/Downlink

70 dB Typical / 75 dB Maximum

2

20 dB Bandwidth (nominal)

Downlink

Uplink (776 - 787 MHz)

27 MHz

Downlink (746 - 757 MHz)

25 MHz

3

Power Output

Uplink

Downlink

Power output for single cell phone (uplink) or single received channel 

(downlink)

28 .7 dBm

25 .5 dBm

4

Power output for multiple channels

Maximum Power

The maximum power is reduced 

by the number of channels:

Number of channels

Uplink

Downlink

2

25 .3 dBm

26 .3 dBm

3

18 .3 dBm

18 .3 dBm

4

19 .3 dBm

20 .2 dBm

5

17 .4 dBm

18 .3 dBm

6

15 .8 dBm

16 .7 dBm

Noise Figure (typical downlink/uplink)

3 .5 dB nominal / 5 dB nominal

Isolation

> 90 dB

Power Requirements

110-240 V AC, 50-60 Hz, 10 W

 Notes:

     1 . Nominal gain is the maximum gain at any frequency in the passband .

     2 . Nominal bandwidth is the difference between two frequencies that are adjacent to the passband where the amplification is 20 dB lower than the passband     

         amplification .  One of the frequencies is lower than the passband and the other is higher .

     3 . The Manufacturer’s rated output power of this equipment is for single carrier operation .  For situations when multiple carrier signals are present, the rating  

         would have to be reduced by 3 .5 dB, especially where the output signal is re-radiated and can cause interference to adjacent band users .  This power  

         reduction is to be by means of input power or gain reduction and not by an attenuator at the output of the device .

     4 . The maximum power for 2 or more simultaneous signals will be reduced by 6 dB every time the number of signals is doubled .

3301 East Deseret Drive, St . George, UT 84790

For additional Technical Support visit  www .WilsonElectronics .com 

or email at: tech@wilsonelectronics .com

Phone: 866-294-1660    Local: 435-673-5021    Fax: 435-656-2432

www .twitter .com/WilsonCellular      www .facebook .com/WilsonCellular

AIG #110996 - Rev1 - 08/25/11

Содержание 4G LTE 700





















Отзывы: