manualshive.com logo in svg

Wilson Electronics 4G LTE 700, Руководство по установке

Поделиться
Скачать
Wilson Electronics 4G LTE 700 Скачать руководство пользователя страница 11

9

10

Contact Wilson Electronics Technical Support Team with any questions at 866-294-1660   

or email: [email protected]. Hours: 7 am to 6 pm MST.

Powering up a Wilson Electronics  

Signal Booster

1 . Never point the front of a Directional Outside Antenna toward the 

Inside Antenna . See Figures 1 & 2 on page 12 .

2 . Ensure that both the Outside Antenna cable and the Inside 

Antenna cable are connected to the Signal Booster

 and the 

connections are tight

 before powering up the Signal Booster .

3 . Plug the power supply into the Signal Booster input marked “6V 

DC” (carefully, to avoid damaging the center pin) and then into a 

wall outlet .

4 . If the Signal Booster does not have a green light (700 MHz) 

please see pages 13 & 14 .

5 . Using multiple Signal Boosters in one installation could cause 

interference to the cell tower .

6 . Contact Wilson Electronics Technical Support Team with any 

questions at 866-294-1660 or email tech@wilsonelectronics .com . 

Technical Support hours are 7 am to 6 pm MST .

Содержание 4G LTE 700





















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды