Wilo Wilo-CronoBloc-BL Скачать руководство пользователя страница 7

English

22

WILO SE 11/2013

Installation and operating instructions

1

General

About this document

The language of the original operating instructions is German. All 
other languages of these instructions are translations of the original 
operating instructions.

These installation and operating instructions are an integral part of 
the product. They must be kept readily available at the place where 
the product is installed. Strict adherence to these instructions is a 
precondition for the proper use and correct operation of the product.

These installation and operating instructions correspond to the rele-
vant version of the product and the underlying safety standards valid 
at the time of going to print.

EC declaration of conformity

A copy of the EC declaration of conformity is a component of these 
operating instructions.

If a technical modification is made on the designs named there with-
out our agreement, this declaration loses its validity.

2

Safety

These operating instructions contain basic information which must 
be adhered to during installation and operation. For this reason, these 
operating instructions must, without fail, be read by the service tech-
nician and the responsible operator before installation and commis-
sioning.

It is not only the general safety instructions listed under the main 
point “safety” that must be adhered to but also the special safety 
instructions with danger symbols included under the following main 
points.

2.1

Indication of instructions in the 
operating instructions

Symbols

General danger symbol

Danger due to electrical voltage

NOTE

Signal words

DANGER!
Acutely dangerous situation
Non-observance results in death or the most serious of injuries.

WARNING!
The user can suffer (serious) injuries. 'Warning' implies that (seri-
ous) injury to persons is probable if this information is disregarded.

CAUTION!
There is a risk of damaging the product/unit. 'Caution' implies that 
damage to the product is likely if this information is disregarded.

NOTE
Useful information on handling the product. It draws attention to 
possible problems.

Содержание Wilo-CronoBloc-BL































Отзывы: