Wilo DrainLift SANI-M Series Скачать руководство пользователя страница 20

Страница: 20 / 32

Installation and electrical connection

WILO SE 2020-05

Residual-current device (RCD)

Install a residual-current device (RCD) in accordance with the regulations of the local
energy supply company.

If people can come into contact with the device and conductive fluids, install a re-
sidual-current device (RCD).

6.5.2

Mains connection

Observe information on the rating plate.

Earth the device in accordance with local regulations.

Install the socket so as to be overflow-proof.

Single-phase current:

–

Shock-proof socket

Three-phase current:

–

CEE16 socket, 5-pole, with neutral conductor

–

Clockwise rotating field

6.5.3

Switchgear

The switchgear is pre-wired and factory-set. Lay all connection cables to the
switchgear and mains connection in accordance with local regulations.

CAUTION! In-

stall the switchgear so as to be overflow-proof!

The switchgear has the following basic functions:

Level-dependent control

Motor protection

Rotation direction monitoring (only for three-phase current)

High water alarm

For detailed information, refer to the installation and operating instructions for the
switchgear:

Electrical connection of the lifting unit to the switchgear

Overview and description of functions

Setting the switching points

Switching points

The switching points of the lifting unit can be adjusted to the positive suction head.
This results in a greater usable volume. The switching point data always refers to the
floor.

Switching points

Setting

DIP switch 3

Factory setting/se-

lectable

Pump ON: 180 mm (7 in)

Pump OFF: 115 mm (4.5 in)

High water alarm: 200 mm (8 in)

1 2 3

•

Pump ON: 250 mm (10 in)

Pump OFF: 115 mm (4.5 in)

High water alarm: 270 mm (10.5 in)

1 2 3

Pump ON: 315 mm (12.5 in)

Pump OFF: 115 mm (4.5 in)

High water alarm: 335 mm (13 in)

1 2 3

Key

• = factory setting, o = adjustable

NOTICE! If the inlet is lower than the switching point “Pump ON”, there is backflow
into the inlet pipe!

NOTICE! For the position of DIP switch 3, refer to the installation and operating in-
structions for the switchgear!

6.5.4

Operation with frequency con-
verter

Operation on the frequency converter is not permitted.

Содержание DrainLift SANI-M Series

































Результаты поиска

Содержание DrainLift SANI-M Series

Отзывы:

Похожие инструкции для DrainLift SANI-M Series

Бренды по названию

Популярные бренды

Wilo DrainLift SANI-M Series, Инструкция по установке и эксплуатации

Результаты поиска

Содержание DrainLift SANI-M Series

Отзывы:

Похожие инструкции для DrainLift SANI-M Series

Бренды по названию

Популярные бренды