Willys CJ-2A Скачать руководство пользователя страница 2

Foreword

IN YOUR possession is a motor vehicle that has been thoroughly tested and inspected. Like any other piece of machinery, to 
maintain it in first class condition, you should lubricate it at the time prescribed with the proper grade of oil and grease and 
keep all working parts and oil holes clean and free of dirt and grit. You should also periodically have it systematically 
inspected at an Authorized Willys-Overland Service Station. 
In the following pages we have set forth the knowledge every owner should have of his vehicle, that he may know to take the 
best care of it and handle it in such a way that he will get maximum service. Information is also available covering external 
adjustments and minor emergency repairs. Read and follow these instructions carefully; we are sure that you will then enjoy 
the satisfactory operation that you rightfully anticipate. 
Should adjustment or repair seem necessary beyond your ability, don't experiment; have the work done by a competent repair 
man. It will always prove best and cheapest in the end to have the work done by the Dealer from whom you purchased your 
car. Many Willys-Overland Dealers have factory trained mechanics and all are familiar with the construction and adjustments 
through the cooperation of the manufacturer. 
Do not attempt any adjustments as long as the vehicle is operating satisfactorily. 
Be sure to obtain the Owner Service Policy, provided by your Dealer on delivery of your new vehicle. 

Caution

 

Accept and use only Genuine Factory Parts

Imitation parts are usually of inferior quality and can do serious damage to other mechanical parts of your vehicle. 
Genuine parts are sold by all authorized Willys-Overland Dealers. Be sure non other than genuine parts are placed in your 
vehicle. 
Presence of parts other than those furnished by Willys-Overland will void the manufacturer's Warranty. 
NOTE: Parts replaced under the terms of the Warranty must be left with the Willys-Overland Dealer who makes the 
replacement, if full credit is expected. 
This is important for Owners to know, when travelling outside the territory in which their vehicle was originally purchased, 
particularly when credit for old parts cannot be established to the satisfaction of the Dealer. 
In this connection, a forwarding address should be given by the Owner in order to insure the credit reaching him. 

Standard Warranty

THE only Warranty under which new Willys-Overland Motor Vehicles are sold is that of the Manufacturer, being the Standard 
Warranty recommended by the Automobile Manufacturer's Association, and is as follows: 

"This is to certify that we, WILLYS-OVERLAND MOTORS, INC., TOLEDO, OHIO, U.S.A. warrant each new 
motor vehicle manufactured by us, to be free from defects in material and workmanship under normal use and 
service, our obligations under this Warranty being limited to making good at our factory any part or parts thereof, 
including all equipment or trade accessories (except tires) supplied by the Car Manufacturer, which shall, within 
ninety (90) days after making delivery of such vehicle to the original purchaser or before such vehicle has been 
driven 4000 miles, whichever event shall first occur, be returned to us with transportation charges prepaid, and 
which our examination shall disclose to our satisfaction to have been thus defective; this warranty being 
expressly in lieu of all other warranties expressed or implied and of all other obligations or liabilities on our part, 
and we neither assume nor authorize any other person to assume for us any other liability in connection with the 
sale of our vehicles. This warranty shall not apply to any vehicle which shall have been repaired or altered 
outside of an Authorized Willys-Overland Service Station in any way so as, in the judgment of the Manufacturer, 
to affect its stability or reliability, nor which has been subject to misuse, negligence or accident" 

The Manufacturer makes no warranty against, nor assumes any liability for any defect in metal or other material in any part, 
device or trade accessory which cannot be discovered by ordinary factory inspection. 

WILLYS-OVERLAND MOTORS, INC.

NOTE -- Willys-Overland Motors, Inc., reserves the right at any time or times to revise, modify, discontinue or change any 
models of its vehicles, or any part or parts thereof, without notice; and, without it or the Seller, incurring any liability or 
obligation to the Purchaser. 

Содержание CJ-2A









































Отзывы: