WIKA DPT-20 Скачать руководство пользователя страница 50

Страница: 50 / 88

6 Set up the sensor with the display and adjustment module

WIKA Operating Instructions - Differential pressure transmitter DPT-20

The instrument settings are copied with this function. The following

functions are available:

•

Read from sensor

: Read data from sensor and store into the

display and adjustment module

•

Write into sensor:

Store data from the display and adjustment

module back into the sensor

The following data or settings for adjustment of the display and ad

justment module are saved:

•

All data of the menu "

Setup

" and "

Display

•

In the menu "

Additional adjustments

" the items "

Reset, Date/

Time

•

The user-programmable linearization curve

The copied data are permanently saved in an EEPROM memory in

the display and adjustment module and remain there even in case of

power failure. From there, they can be written into one or more sen

sors or kept as backup for a possible electronics exchange.

Note:

Before the data are saved in the sensor, a safety check is carried out

to determine if the data match the sensor. In the process the sensor

type of the source data as well as the target sensor are displayed. If

the data do not match, a fault message is outputted or the function is

blocked. The data are saved only after release.

In this menu item, the units for the DP flow element are determined

and the selection of mass or volume flow is carried out.

Furthermore the adjustment for the volume or mass flow rate at 0 % or

100 % is carried out.

In this menu item you gain access to the protected area where

you can enter special parameters. In exceptional cases, individual

parameters can be modified in order to adapt the sensor to special

requirements.

Change the settings of the special parameters only after having con-

tacted our service staff.

Copy instrument settings

Characteristics values DP

flow element

Special parameters

Содержание DPT-20

























































































Результаты поиска

Содержание DPT-20

Отзывы:

Похожие инструкции для DPT-20

Бренды по названию

Популярные бренды

WIKA DPT-20, Руководство по эксплуатации

Результаты поиска

Содержание DPT-20

Отзывы:

Похожие инструкции для DPT-20

Бренды по названию

Популярные бренды