WIKA DPT-20 Скачать руководство пользователя страница 16

Страница: 16 / 88

4 Mounting

WIKA Operating Instructions - Differential pressure transmitter DPT-20

Note:

Follow the mounting instructions of the respective manufacturer and

seal the thread, e.g. with PTFE tape.

Valve blocks are used for initial shut-off when connecting the differ

ential pressure transmitter to the process. They are also used for pres

sure compensation of the measuring chambers during adjustment.

3-fold and 5-fold valve blocks are available (see chapter "

Mounting

and connection instructions

").

Free openings on the process assembly must be closed by ventilation

valves or closing screws. Required torque see chapter "

Technical

data

Note:

Use the supplied parts and seal the thread with four layers of PTFE

tape.

4.4 Mounting and connection instructions

When connecting DPT-20 to the measuring point, take note of the

high/low pressure side of the process component.

The "

" identifies the high pressure side, the low pressure side due

to an "

" on the process component next to the oval flanges.

Note:

The static pressure is measured on the low pressure side "

H L

Fig. 9: Marking for high/low pressure side on the process component

1 H = High pressure side

2 L = Low pressure side

Valve blocks

Ventilation valves, closing

screws

Connection high/low

pressure side

The pressure effective on "H" is considered as positive, the pressure effec

tive on "L" as negative in the calculation of the pressure difference.

Содержание DPT-20

























































































Результаты поиска

Содержание DPT-20

Отзывы:

Похожие инструкции для DPT-20

Бренды по названию

Популярные бренды

WIKA DPT-20, Руководство по эксплуатации

Результаты поиска

Содержание DPT-20

Отзывы:

Похожие инструкции для DPT-20

Бренды по названию

Популярные бренды