WIKA DPT-20 Скачать руководство пользователя страница 47

Страница: 47 / 88

6 Set up the sensor with the display and adjustment module

WIKA Operating Instructions - Differential pressure transmitter DPT-20

6.5.3 Diagnostics

In this menu item, the device status is displayed.

In case of error, e.g. the error code F017, e.g. the error description "

Adjustment span too small

" and a four digit figure are displayed for

service purposes. You can find the error codes with description, rea

son as well as rectification in chapter "

Asset Management

The respective min. and max. measured values for the differential

pressure and static pressure are stored in the sensor. In menu item "

Peak value, pressure

", both values are displayed.

In another window you can carry out a reset of the peak values

separately.

The respective min. and max. measured values of the measuring cell

and the electronics temperature are stored in the sensor. In menu

item "

Peak value, temperature

", both values are displayed.

In another window you can carry out a reset of the two peak values

separately.

In this menu item you can simulate measured values. This allows the

signal path to be tested, e.g. through downstream indicating instru

ments or the input card of the control system.

Select the requested simulation variable and set the requested value.
To deactivate the simulation, you have to push the

[ESC]

key and

confirm the message "

Deactivate simulation

" with the

[OK]

key.

Device status

Peak value, pressure

Peak value, temperature

Simulation bus systems

Содержание DPT-20

























































































Результаты поиска

Содержание DPT-20

Отзывы:

Похожие инструкции для DPT-20

Бренды по названию

Популярные бренды

WIKA DPT-20, Руководство по эксплуатации

Результаты поиска

Содержание DPT-20

Отзывы:

Похожие инструкции для DPT-20

Бренды по названию

Популярные бренды