manualshive.com logo in svg

White Industries Diagnostic 1090AT, Руководство по эксплуатации и обслуживанию

Поделиться
Скачать
White Industries Diagnostic 1090AT Скачать руководство пользователя страница 7

5

Safety Information

WARNING

Risk of explosion if improper tank is used.
Do not use any tank with this equipment
other than the one originally provided.
These tanks are D.O.T. certified for
refilling. D.O.T certified tanks are
marked "D.O.T. 4BA 350" or "D.O.T. 4BA
400".
Explosion can cause injury.

WARNING 

Removing tubing assemblies may discharge
refrigerant.
Wear safety goggles and protective
gloves, user and bystander.

Everyday

eyeglasses only have impact resistant
lenses, they are NOT safety glasses.
Refrigerant may cause injury.

WARNING 

A test vehicle may move if not properly
prepared.

• Block the drive wheels before

performing a test with the engine
running. Unless instructed otherwise,
set the parking brake and put the gear
selector in neutral (manual
transmission) or park (automatic
transmission). If the vehicle has an
automatic parking brake release,
disconnect the release mechanism for
testing and reconnect when testing is
completed.

• Do not leave a running engine

unattended.

A moving vehicle can cause injury.

CAUTION

Risk of injury.
This equipment should be operated by
qualified personnel.
Operation of your 1090AT diagnostic™ unit
by anyone other than qualified personnel
may result in injury.

CAUTION

Risk of refrigerant leakage.
Always close the service valves and the
control panel valves before
disconnecting a hose coupling.
A loosened hose coupling can leak
refrigerant into the atmosphere.

CAUTION

Misdiagnosis may lead to incorrect or
improper repair and/or adjustment.
Do not rely on erratic, questionable, or
obviously erroneous test information or
results. If test information or results are
erratic, questionable, or obviously
erroneous, make sure that all
connections and data entry information
are correct and that the test procedure
was performed correctly. Refer also to
the 

Maintenance and make repairs as

required. If test information or results
are still suspicious, do not use them for
diagnosis. Contact your 

WHITE

®

Representative.
Improper repair and/or adjustment may
cause vehicle or equipment damage or
unsafe operation.

WARNING

Risk of explosion.

• Some vehicle fuel systems such as

Mercedes, light trucks, and some Fiat
models have the same service fittings
as the A/C systems.

• Do not connect to similar fuel service

fittings.

• Connect only to A/C service fittings.
If you mistakenly connect to fuel system:
• Do not use switches as this may cause

sparks.

• Do not move any metal items as this

may cause sparks.

• Unplug unit’s power cord from the wall

outlet.

• Immediately ventilate the work area

and call your local service
representative.

Fuel in A/C recovery unit can explode and
cause injury.

SAVE THESE

INSTRUCTIONS

For Reference Only

Содержание Diagnostic 1090AT

































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды