manualshive.com logo in svg

White Industries Diagnostic 1090AT, Руководство по эксплуатации и обслуживанию

Поделиться
Скачать
White Industries Diagnostic 1090AT Скачать руководство пользователя страница 29

27

Maintenance

Maintaining the Vacuum
Pump

Checking Vacuum Pump Oil
Level

1. Look through oil level sight glass to verify

vacuum pump oil level.

2. Oil level should appear to be in the

middle of the sight glass.

3. If oil is low, add oil to vacuum pump, refer

to 

Adding Oil to Vacuum Pump.

Adding Oil to Vacuum Pump

Follow this procedure to add oil to the
vacuum pump.

1. Turn power OFF to the 

1090AT

diagnostic™ unit and remove power cord
from wall outlet.

2. Remove all screws located around the

lower edge of the plastic top cover.

3. Gently lift the plastic top cover off the

unit.

4. Lift the hinged control panel up and lay

towards the back of the unit.

5. Remove oil fill screw cap.

Figure 5: Vacuum Pump Fill Cap

6. Add oil to vacuum pump fill port until the

oil is visible halfway up the sight glass.

7. Install the oil fill screw cap.

8. Replace control panel to original position.

9. Replace plastic top cover and screws.

Changing Vacuum Pump Oil

The vacuum pump oil must be changed at
least every 6 months. The oil may have to
be changed earlier if the oil is no longer
clear when viewed through the sight glass.

1. Turn power OFF to the 

1090AT

diagnostic™ unit and remove power cord
from wall outlet.

WARNING

• Wear safety goggles and protective

gloves, user and bystander. Everyday
eyeglasses only have impact resistant
lenses, they are NOT safety glasses. If
any refrigerant gets into eyes, flush
with water and seek a doctor’s aid
immediately, even though irritation
may cease.

• Prevent refrigerant from contacting the

skin.

• Read, understand and follow 

Safety

Information in the front of this manual.

2. Put a container under the oil drain tube of

the vacuum pump.

3. Remove the oil drain screw cap and drain

oil.

✓

✓

✓

✓

Discard refrigerant oil in
accordance with local, state and
federal regulations that apply in
your area.

4. Install the oil drain screw cap.

5. Refill vacuum pump with oil, refer to

Adding Oil to Vacuum Pump.

For Reference Only

Содержание Diagnostic 1090AT

































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды