manualshive.com logo in svg

White Industries Diagnostic 1090AT, Руководство по эксплуатации и обслуживанию

Поделиться
Скачать
White Industries Diagnostic 1090AT Скачать руководство пользователя страница 30

28

Maintenance

Changing Identifier Filter

If the identifier option is installed. Replace
the white refrigerant identifier filter when it
starts to show color changes to pink or red.

1. Turn power OFF to the 

1090AT

diagnostic™ unit and remove power cord
from wall outlet.

2. Gently pull filter out of holding bracket.

3. Disconnect lines to filter.

✓

✓

✓

✓

Dispose of filter according to local,
state and federal regulations that
apply in your area.

4. Connect lines to new filter, paying

attention to flow markings on filter.

5. Mount new filter in holding bracket.

Replacing Printer Paper

Follow this procedure to replace printer
paper.

1. Open the printer access door.

2. Place new printer paper roll inside.

3. Close access door with edge of paper

hanging out.

Storing the 

1090AT

diagnostic™ Unit

Follow this procedure when storing your
1090AT diagnostic™ unit for prolonged
periods (3 months or more) of time.

✓

✓

✓

✓

Storage temperature should not
exceed the limits of -4° to 140°F.

1. Change the vacuum pump oil. Refer to

Changing Vacuum Pump Oil.

2. Close both hand valves on the recovery

and virgin tanks.

3. Remove the yellow hose from the

recovery tank.

4. Close both service hose couplers.

Replacement Parts

Part Number 

Description

1-27280 ................ Service Fitting, Low-side
1-27180 .............. Service Fitting, High-side
EAK0027C00AS ............ Coupler Repair Kit
1-15080  .............. Low-side Adapter Fitting
1-9881 .......................... Master Filter/Dryer
EAK0227L01A  .......... Vacuum Pump Oil Kit
EAK0218L33A  .. 10 Micron Filter Kit, 10pcs
EAA0253L62A .... Recovery Tank, 50 pound

Upgrade Kits

EEAC720ACV .................................. Cover
EAK0218L23A  ........ Temperature Probe Kit

Service only installable kits.
EAK0218L22A .............. Identifier 

Upgrade

EEAC300A1 ........................ Identifier Filter
EAK0218L21A .................. Printer Upgrade
8-00910A ................ Printer Paper, Thermal

For service or to order replacement parts
contact an authorized 

WHITE® service

center or call 1-800-225-5786.

For Reference Only

Содержание Diagnostic 1090AT

































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды