manualshive.com logo in svg

White Industries Diagnostic 1090AT, Руководство по эксплуатации и обслуживанию

Поделиться
Скачать
White Industries Diagnostic 1090AT Скачать руководство пользователя страница 5

3

Safety Information

IMPORTANT SAFETY
INSTRUCTIONS

WARNING

Risk of a lack of oxygen.

• Vehicle exhaust gases contain carbon

monoxide.

• Refrigerant gas can displace air in work

area.

Use your 

1090AT diagnostic™ unit in

locations with mechanical ventilation
providing at least four air changes per
hour.
Impairment of breathing can cause injury.

Power

WARNING

Risk of electric shock and fire.

• To avoid electric shock the power cord

protective grounding conductor must
be connected to a properly grounded
A.C. outlet.

• Use proper A.C. outlet for unit to

operate correctly. See unit ID plate on
back of unit. Extension cords  are not
recommended. If an extension cord is
necessary, then use:
— 16 AWG for cords up to 50 feet 

long, and

— 14 AWG for cords greater than 50 

feet but less than 100 feet long.

• Connect power cord to properly

grounded outlet.

• Do not remove or bypass the

grounding pin.

• Do not use on wet surfaces or expose

to rain.

• Use only fuses with the rating

specified near the fuse holder.

Electric shock and fire can cause injury.

Refrigerant

WARNING

Risk of expelling refrigerant under pressure.

• Wear safety goggles and protective

gloves, user and bystander. Everyday
eyeglasses only have impact resistant
lenses, they are NOT safety glasses. If
any refrigerant gets into eyes, flush
with water and seek a doctor's aid
immediately, even though irritation
may cease.

• Do not remove master filter/dryer while

under pressure. Perform maintenance
procedure for removing master
filter/dryer, refer to

Changing the

Master Filter/Dryer.

• Prevent refrigerant from contacting the

skin.

Expelled refrigerant can cause injury.

WARNING

Risk of explosion.

• Do not use compressed shop air for

leak detection or to pressure test a
system containing refrigerant.
Refrigerant can form combustible
mixtures at pressures above
atmospheric and with air
concentrations greater than 60% by
volume.

• Do not heat a container of refrigerant

above 125°F (52°C).

Explosion can cause injury.

WARNING 

Risk of fire.

• Do not use this equipment in the

vicinity of spilled or opened containers
of gasoline.

• Do not use your 

1090AT diagnostic™

unit or leak detector equipment if R-12
substitutes are suspected. R-12
refrigerant substitutes may be
flammable.

Fire can cause injury.

For Reference Only

Содержание Diagnostic 1090AT

































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды