Whirlpool WSE 2930 W Скачать руководство пользователя страница 84 | Manualshive

Страница: 84 / 101

background image

Troubleshooting

Filter reset after Built-In test sequence

Water Filter Indicator Factory / Service reset:

Press 4 times consecutively (within 10 sec) the water valve shaft switch.
The symbol “F” on the Refrigerator display will be shown in order to confirm the operation.
If a alarm code alarm is being showing, the symbol “F” will cycle together with them.

Antibacterial Filter Indicator Factory/Service reset:

Press 4 times consecutively (within 10 sec) the refrigerator compartment door switch.
The symbol “A” on the Freezer display shall be shown in order to confirm the operation.
If a alarm code is being showing, the symbol “F” will cycle together with them.

At the end of the Built-In Test is and all was OK, it will be displayed the code 00 till the
Built-In Test is completed.

At this time it will be possible to reset to „0“ the Water Filter Indication and / or the
Antibacterial Filter Indication in the following way:

«
...
82
83
84
85
86
...
»

Содержание WSE 2930 W






































































































Отзывы:

Нет отзывов

Похожие инструкции для WSE 2930 W

SIDE-BY-SIDE REFRIRATOR 22

Бренд: GEAppliances Страницы: 92

Бренд: Samsung Страницы: 42

Бренд: FRENZEL Страницы: 23

Бренд: Gorenje Страницы: 28

Бренд: Infiniton Страницы: 28

Бренд: ZANKER Страницы: 44

Бренд: Baumatic Страницы: 28

Бренд: Norcold Страницы: 4

Бренд: Philco Страницы: 27

Бренд: Fagor Страницы: 19

Бренд: Galanz Страницы: 6

Бренд: ZANKER Страницы: 32

Бренд: essentiel b Страницы: 64

Бренд: Marvel Страницы: 12

Бренд: Midea Страницы: 12

FreedomT24UR925LS

Бренд: Thermador Страницы: 68

Бренд: Reeva Страницы: 17

MASTERCHEF EXECUTIVE PSC-WG-1020

Бренд: Sam Cook Страницы: 32

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды