Whirlpool WSE 2930 W Скачать руководство пользователя страница 30

Страница: 30 / 101

Operation

“Virtual Key’s” on 7-segment

Virtual Key 1:

Child Lock

function for the User Interface:

To activate or deactivate the child lock function press the button “reset alarm” and “vacation mode
simultaneous for 2 seconds. This function is only available for appliance with dispenser unit.

Virtual Key 2:

Niche Heater

function:

To turn ON or OFF the niche heater in the dispenser area, press the button “fast freezing” and “reset

alarm” at the same time for 2 seconds. This function is only available for appliance with dispenser unit.

Virtual Key 3:

Eco function

To activate or deactivate the “Eco function” press the button ”ice & water mode” and “reset alarm” at
the same time for 2 seconds.

Содержание WSE 2930 W






































































































Результаты поиска

Содержание WSE 2930 W

Отзывы:

Похожие инструкции для WSE 2930 W

Бренды по названию

Популярные бренды

Whirlpool WSE 2930 W, Руководство пользователя

Результаты поиска

Содержание WSE 2930 W

Отзывы:

Похожие инструкции для WSE 2930 W

Бренды по названию

Популярные бренды