Whirlpool WRF954CIHB Скачать руководство пользователя страница 17 | Manualshive

Страница: 17 / 59

background image

For Service Technician Use Only

DIAGNOSTICS

French-Door Bottom Mount Refrigerator

n

1-13

Machine Compartment Components

Sealed System with Check Valve

The sealed system uses a new, linear compressor to drive the

refrigeration cycle.

Refrigerant is pumped through the condenser and a non-UV dye

drier to the three-way valve. The three-way valve aligns to allow

refrigerant to either the RC or FC evaporator, depending on which

is being cooled. A check valve is positioned at the outlet of the

FC Evaporator to prevent refrigerant back flow during RC cooling.

The linear compressor takes a suction of the evaporator outlet of

the compartment being cooled.

Sealed System without Check Valve

Refrigerant flow has been updated to make the refrigerator more

efficient. The check valve that prevents refrigerant from one

evaporator to the other was eliminated.

While cooling the freezer section, due to the low pressure in

the capillary tubing, the refrigerant will be in the evaporator of

refrigerator compartment but will not be flowing through the

coil. The tubing was re-routed for the refrigerator evaporator to

go through the freezer evaporator to keep it cold then back the

compressor. The freezer fan does not run during this time.

One Way
Check Valve

One Way
Check Valve

Cooling Freezer

Cooling Refrigerator

Cooling Freezer

Cooling Refrigerator

«
...
15
16
17
18
19
...
»

Содержание WRF954CIHB




























































Отзывы:

Нет отзывов

Похожие инструкции для WRF954CIHB

Бренд: GE Страницы: 48

Бренд: Cafe Страницы: 80

Бренд: Oypla Страницы: 7

Бренд: La Sommeliere Страницы: 21

WINE CAPTAIN 2175BEVC

Бренд: U-Line Страницы: 2

Бренд: Continental Refrigerator Страницы: 2

Бренд: NEFF Страницы: 40

Бренд: Zokop Страницы: 9

Бренд: Thermador Страницы: 68

Бренд: Laurus Страницы: 128

600 Series BI-42SD

Бренд: Wolf Страницы: 2

Бренд: Hanseatic Страницы: 64

Бренд: Smeg Страницы: 16

Бренд: Westinghouse Страницы: 20

Бренд: Zanussi Страницы: 20

Бренд: Haier Страницы: 32

Бренд: Haier Страницы: 36

Бренд: Haier Страницы: 38

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды