Whirlpool WRF954CIHB Скачать руководство пользователя страница 32

Страница: 32 / 59

For Service Technician Use Only

DIAGNOSTICS

1-28

French-Door Bottom Mount Refrigerator

Dispenser and IB Duct Heater (Door) Troubleshooting

Remove dispenser UI and locate Dispenser heater wiring connector (2 wire connector, 1 red, 1 white).

Heater Resistance Checks

•

Disconnect the 2 Pin Connector (Figure 8).

•

Take resistance reading on side leading to visible heater

(Dispenser Heater). Reading should be ≈108 ohms.

•

Take resistance reading on other side of connector (IM Duct

Heater--Door). Reading should be ≈108 ohms.

Run Service Test 70 - Dispenser Heater Test

•

Ensure LED display shows “on”

•

If LED display does not show “on”, replace Dispenser UI.

If all checks are OK and problems persist:

Run Service Test 87 - Dispenser Heater Activation Mode

•

Use up or down arrow to change activation mode to “01”

•

Press the “Icemaker2” key to confirm selection.

Mullion Heater

The Mullion heater resistance can be checked at multiple points. The easiest is under the left hinge cover, or at the heater itself.

Heater Resistance Checks

Check the resistance of the Mullion Heater. Reading

should be ≈17 ohms.

Run Service Test 63 - Vertical Mullion Heater Test

•

Ensure LED display shows “on”

•

If LED display does not show “on”, replace Eyebrow UI.

If all checks are OK and problems persist:

Run Service Test 85 - Vertical Mullion Heater Activation Mode

•

Use up or down arrow to change activation mode to “01”

•

Press the “Icemaker2” key to confirm selection.

J8-2

Dispenser UI

Pin 2

+12.7 VDC

Pin 1

J8-1

Neutral

IM Duct

Heater

Dispenser

Heater

2 Pin Connector

behind Dispenser UI

at Mullion Heater

2 Pin Connector

J2-3

Eyebrow UI

Pin 2

+ 14 VDC

Pin 1

J2-4

Neutral

BK/YL

Mullion

Heater

Pin 1

in 1

Pin 2

BK/YL

2 Pin Connector

Left Hinge Cover

behind Dispeser UI

4 Pin Connector

Содержание WRF954CIHB




























































Результаты поиска

Содержание WRF954CIHB

Отзывы:

Похожие инструкции для WRF954CIHB

Бренды по названию

Популярные бренды

Whirlpool WRF954CIHB, Руководство по обслуживанию

Результаты поиска

Содержание WRF954CIHB

Отзывы:

Похожие инструкции для WRF954CIHB

Бренды по названию

Популярные бренды