Whirlpool WRF954CIHB Скачать руководство пользователя страница 53

Страница: 53 / 59

COMPONENT ACCESS

French-Door Bottom Mount Refrigerator

3-11

Thermistor and Possible Frost Build-Up (Continued)

Model

Evaporator Cover Part

KRFC604FS*

W10865106

KRFC704FS*

W10815735

JFFCC72EF*

W10815734

WRF992FIF*

W10875099

WRF993FIF*
WRF995FIF*

The photos below are showing the new correct gaskets installed

properly.

Defrost the refrigerator section evaporator to ensure it is

completely free of Ice and frost before installing new cover

to insure proper operation. When using a heat source to

defrost the refrigerator section evaporator cover, care should

be exercised not to overheat the plastic surface of the cover

or the polystyrene foam behind the cover. Doing so can

permanently damage these components.

To insure proper sealing of the replacement refrigerator

section evaporator cover, be sure that the refrigerant lines

that connect the evaporator do not come in contact with the

replacement cover.

If tubing was pulled out for any service access, it should be

moved back to appropriate position before installing cover.

Suction tube and evaporator inlet (cap tube with mastic

around) must be contained entirely inside projection of back

wall.

Suction tube and evaporator inlet (cap tube with mastic

around) must be contained, front to back, entirely within

depth of evaporator.

Gasket is missing

Содержание WRF954CIHB




























































Результаты поиска

Содержание WRF954CIHB

Отзывы:

Похожие инструкции для WRF954CIHB

Бренды по названию

Популярные бренды

Whirlpool WRF954CIHB, Руководство по обслуживанию

Результаты поиска

Содержание WRF954CIHB

Отзывы:

Похожие инструкции для WRF954CIHB

Бренды по названию

Популярные бренды