Whirlpool WRF954CIHB Скачать руководство пользователя страница 2

Страница: 2 / 59

French-Door Bottom Mount Refrigerator

FORWARD

This Whirlpool Service Manual (Part No. W11366204), provides the In-Home Service Professional with service

information for the “French-Door Bottom Mount Refrigerator.”

The Wiring Diagram used in this Service Manual is typical and should be used for training purposes only. Always

use the Wiring Diagram supplied with the product tech sheet when servicing the refrigerator.

For specific operating and installation information on the model being serviced, refer to the “Use and Care

Guide” or “Installation Instructions” provided with the refrigerator.

GOALS AND OBJECTIVES

The goal of this Service Manual is to provide information that will enable the In-Home Service Professional to

properly diagnose malfunctions and repair the “French-Door Bottom Mount Refrigerator.”

The objectives of this Service Manual are to:

•

Understand and follow proper safety precautions.

•

Successfully troubleshoot and diagnose malfunctions.

•

Successfully perform necessary repairs.

WHIRLPOOL CORPORATION assumes no responsibility for any repairs made on our

products by anyone other than authorized In-Home Service Professionals.

Содержание WRF954CIHB




























































Результаты поиска

Содержание WRF954CIHB

Отзывы:

Похожие инструкции для WRF954CIHB

Бренды по названию

Популярные бренды

Whirlpool WRF954CIHB, Руководство по обслуживанию

Результаты поиска

Содержание WRF954CIHB

Отзывы:

Похожие инструкции для WRF954CIHB

Бренды по названию

Популярные бренды