26
1.
Place a sturdy measuring cup (1-cup [
0.2 L
] size) on the
dispenser tray centered in front of the ice/water dispenser
paddle.
NOTE:
Depending on your model, a measuring cup may be
provided.
Ensure that you do not have any Measured Fill preset selected.
2.
Touch and hold the Measured Fill button for 3 seconds
to enter into Calibration mode. The Calibration icon and
Measured Fill icon will illuminate and remain lit while the
Measured Fill feature is being calibrated.
NOTE:
You may touch MEASURED FILL to exit at any time in
Calibration mode. The Calibration and Measured Fill icons will
disappear.
3.
Press and hold the water dispenser paddle, as needed, to
dispense water to the 1-cup fill line in the measuring cup.
NOTE:
If overfilling or spilling occurs, discard the water and
restart the calibration process.
4.
When 1 cup of water has been correctly dispensed into
the measuring cup, touch MEASURED FILL to confirm the
calibration.
5.
When Measured Fill calibration has been confirmed, the
Calibration icon will disappear and the display will return
to the home screen.
Dispensing
Touch CUBED ICE or CRUSHED ICE for your ice selection.
NOTES:
n
For crushed ice, cubes are crushed before being dispensed.
This may cause a slight delay when dispensing crushed ice.
Noise from the ice crusher is normal and pieces of ice may
vary in size.
n
When changing from crushed to cubed, a few ounces of
crushed ice will be dispensed along with the first cubes.
Dispensing Water
IMPORTANT:
n
Dispense at least 1 qt (1 L) of water every week to maintain
a fresh supply.
n
If the flow of water from the dispenser decreases, it could
be caused by low water pressure.
n
With the water filter removed, dispense 1 cup (
0.2 L
)
of water. If 1 cup (
0.2 L
) of water is dispensed in
8 seconds or less, the water pressure to the refrigerator
meets the minimum requirement.
n
If it takes longer than 8 seconds to dispense 1 cup
(
0.2 L
) of water, the water pressure to the refrigerator is
lower than recommended. See the “Water Supply
Requirements” and “Troubleshooting” sections for
suggestions.
To Dispense Water - Standard:
1.
Press a sturdy glass against the water dispenser paddle.
2.
Remove the glass to stop dispensing.
NOTE:
The Dispense Water button does not enable standard
dispensing. It only functions in Measured Fill mode.
To Dispense Water - Measured Fill:
Measured Fill allows you to dispense a specified amount
of water with the touch of a few buttons.
1.
Put a sturdy glass under water spout. Touch
MEASURED FILL to activate.
NOTE:
The amount of water you select will be dispensed.
Make sure the container can hold the entire volume. If ice
is in the container, you may need to adjust your selection.
2.
Touch MEASURED FILL to turn on, then touch to select
8 oz (0.2 L), 16 oz (0.5 L), or
32
oz (
1
L). Touch the fourth
time
to exit Measured Fill display.
3.
Touch DISPENSE WATER (center button) or press paddle and
the selected amount of water will be dispensed.
NOTES:
n
The Measured Fill dispenser will automatically time out after
1 minute of inactivity.
n
You can refill several glasses with the same measurement by
continuing to touch DISPENSE WATER (center button) after
each glass fill.
Measured Fill options are listed in the following chart:
Units
Ounces
8
16
32
Cups
1
2
4
Liters
0.2
0.5
1
NOTE:
Most coffee cups (commonly 4 to 6 oz [118 to 177 mL]
per cup) are not the same size as a measuring cup (8 oz [
0.2 L
]).
You may need to recalibrate Measured Fill to underfill or to
avoid unintentionally overfilling coffee cups.
4.
Dispense water.
NOTE:
While dispensing water, the flow of water will
automatically stop once the desired volume has been
dispensed.
n
Press a sturdy glass against the dispenser paddle below
the water spout.
OR
n
Place the glass below the water spout and touch
DISPENSE WATER for hands-free dispensing.
5.
To pause dispensing before the selected volume has been
dispensed, touch DISPENSE WATER a second time or touch
the water dispenser paddle. Touch DISPENSE WATER or
paddle again to resume dispensing remaining amount.
NOTE:
If you stop dispensing before the desired volume has
been dispensed, the display will turn off after 1 minute. If you
have not resumed by then, it will reset back to the original
amount.
6.
To select a new volume or start dispensing the same volume
again, you must first finish dispensing the selected volume or
turn off the Measured Fill feature (either by waiting 1 minute,
so it will automatically turn off, or by touching CUBED ICE
or CRUSHED ICE to manually turn it off), and then select
Measured Fill again.
A
B
C
A. Water dispenser paddle
B. Ice dispenser paddle
C. Measuring cup (1 cup)
