Whirlpool MVWC450XW4, Руководство пользователя

Страница: 18 / 48

PAGE 18
FOR SERVICE TECHNICIAN’S USE ONLY
DO NOT REMOVE OR DESTROY
2. Check the drain pump and electrical
connections by performing the Drain Test under
Manual Test Mode on page 9. The following
steps assume that this step was unsuccessful.
3. Unplug washer or disconnect power.
4. Remove console to access main control.
5. Visually check that the J16 connector is
inserted all the way into the main control.

If visual check passes, go to step 6.

If connector is not inserted properly,
reconnect J16 and repeat step 2.
6. Remove connector J16 from main control.
With an ohmmeter, verify resistance values shown
below across the following J16 connector pinouts:
Resistance should be 14 –25
Ω
.

If values are open or out of range, go to step 7.

If values are correct, go to step 11.
7. Tilt washer back to access drain pump.
Verify pump is free from obstructions.
8. Visually check the electrical connections
at the drain pump.

If visual check passes, go to step 9.

If connections are loose, reconnect the
electrical connections and repeat step 2.
9. With an ohmmeter, check harness for
continuity between the drain pump and main
control. See chart below.

If there is continuity, go to step 10.
 If there is no continuity, replace the lower
machine harness and repeat step 2.
10. With an ohmmeter, measure the resistance
across the two pump terminals. Resistance
should be 14–25
Ω
.

If values are open or out of range, replace
the pump motor.

If the resistance at the pump motor is
correct, go to step 11.
11. If there is a stuck pump, check for a blown
board. If the board has a blown R244 surge
resistor, check for stuck or shorted pump
motor; if OK, check all other loads with input
to the board.
12. If the preceding steps did not correct the
drain problem, replace the main control.
a. Unplug washer or disconnect power.
b. Replace the main control.
c. Reassemble all parts and panels.
d. Plug in washer or reconnect power. Calibrate
washer and perform Automatic Test to verify repair.
TEST #8: Lid Lock
Perform the following checks if the washer
does not lock (or unlock).
1. Perform the Lid Lock test under Manual
Test Mode on page 9. The following steps
assume that this step was unsuccessful.
2. Check lid lock mechanism for obstruction
or binding. Repair as necessary.
3. Unplug washer or disconnect power.
4. Remove console to access main control.
5. Visually check that the J15 connector is
inserted all the way into the main control.

If visual check passes, go to step 6.
 If connector is not inserted properly,
reconnect J15 and repeat step 1.
6. Remove connector J15 from main control.
With an ohmmeter, verify lid lock resistance
values shown below across the following J15
connector pinouts:
 If resistance values are good, go to step 7.

If switch measurements do not match the
values shown in the table for unlocked (or
locked) condition, a problem exists in the
lid lock. Replace the lid lock mechanism.
7. If the preceding steps did not correct the
lock problem, replace the main control.
a. Unplug washer or disconnect power.
b. Replace the main control.
c. Reassemble all parts and panels.
d. Plug in washer or reconnect power. Calibrate
washer and perform Automatic Test to verify repair.
Component J16 Connector Pinout
Drain Pump J16, 2 & 3
Main Control to Drain Pump
Drain Pump Pin-1 to Main Control J16-3
Drain Pump Pin-2 to Main Control J16-2
Component
Lock Switch
Solenoid
J15-1 J15-3
4 - 5 1 J 3 - 5 1 J h c ti w S k c o L
2 - 5 1 J 3 - 5 1 J h c ti w S d i L
Contacts
Measured
LID LOCK RESISTANCE
Lid Closed = 0 ohms
Lid Open = Open Circuit
85 to 155 ohms
Locked = 0 ohms
Unlocked = Open Circuit
Resistance