background image

21

Replacement Parts

IMPORTANT: The following maintenance procedures 
are for the Flame Lock

 Safety System components and 

should be performed by a qualified person.

Replacement parts may be ordered through your plumber 
or the local distributor. Parts will be shipped at prevailing 
prices and billed accordingly. When ordering replacement 
parts, always have the following information ready:

1.  model, serial, and product number

2. type 

of 

gas

3. item 

number

4. parts 

description

See pages 27-28 for a list of available repair parts.

Removing the Manifold Assembly

1.  Turn off the gas to the water heater at the manual gas 

shut-off valve (Figure 3).

2.  Turn the gas control/temperature knob to the “OFF” 

position (Figure 19).

3.  Remove the outer door.

4.  Remove the two screws 

securing the manifold door 
to the combustion chamber 
(Figure 23).

5. Disconnect 

the 

thermopile, 

pilot tube, the igniter wire 
from the igniter button, the 
two connectors attached 
to the thermal switch, and 
manifold tube at the gas 
control valve/thermostat. 
(Figures  22 & 23.) 

6.  Grasp the manifold tube 

and push down slightly to 
free the manifold tube, pilot tube, and thermopile.

7.  Carefully remove the manifold assembly from the 

combustion chamber. NOTE: Be sure not to damage 
internal parts. 

Removing the Burner from the 
Manifold Assembly

Natural Gas Burner (Low Nox)

1.  Take off the burner by removing the two (2) screws 

located underneath the burner.

2.  Check the burner to see if it is dirty or clogged. The 

burner may be cleaned with soap and hot water (Figure 
24).

Figure 22
Gas Control Valve/
Thermostat

Igniter
Wire

Thermopile Wire

Pilot Tube

Manifold
Tube

Igniter
Button

Figure 23
Manifold Assembly
Removal

Manifold Screw (2)

Two Piece Wire Connector

Manifold Door

Thermal Switch

Pilot Tube

Manifold Tube

Viewport

Thermopile

Piezo Igniter Button

Gas Valve/Thermostat

Figure 24
Natural gas (Low NOx)
Manifold Assembly

Pilot Assembly

Burner

Thermal Switch

Viewport

Manifold Door

Door Gasket

Thermopile

Pilot Tube

Manifold Tube

Two Piece Wire

Connector

Pilot Bracket

Igniter Wire

Screws

Burners

Pilot Assembly

Manifold Tube

Manifold Door

Pilot Tube

Thermopile Connector

Содержание energysmart Residential Electric Water Heater





























Отзывы: