Westfield WCX 1335 Скачать руководство пользователя страница 9

Страница: 9 / 62

30998 R1

2.6. Tire Safety

Failure to follow proper procedures when mounting a tire on a
wheel or rim can produce an explosion that may result in
serious injury or death.

• DO NOT attempt to mount a tire unless you have the proper

equipment and experience to do the job.

• Have a qualified tire dealer or repair service perform

required tire maintenance.

• When replacing worn tires, make sure they meet the original

tire specifications. Never undersize the replacement tire.

• DO NOT weld to the tire rim with the tire mounted on the

rim. This action may cause an explosion which could result in
serious injury or death.

• Inflate tires to the manufacturer’s recommended pressure.

• Tires should not be operated at speeds higher than their

rated speed.

• Keep wheel lug nuts tightened to manufacturer’s

recommendations.

• Never reinflate a tire that has been run flat or seriously

under-inflated without removing the tire from the wheel.
Have the tire and wheel closely inspected for damage before
remounting.

2.7. Personal Protective Equipment

The following Personal Protective Equipment (PPE) should be worn when assembling the equipment.

Safety Glasses

• Wear safety glasses at all times to protect eyes from debris.

Work Gloves

• Wear work gloves to protect your hands from sharp and rough edges.

Steel-Toe Boots

• Wear steel-toe boots to protect feet from falling debris.

WCX 1335 TOP-DRIVE CONVEYOR – PORTABLE GRAIN BELT CONVEYOR

2. SAFETY

Содержание WCX 1335































































Результаты поиска

Содержание WCX 1335

Отзывы:

Похожие инструкции для WCX 1335

Бренды по названию

Популярные бренды

Westfield WCX 1335, Инструкция по сборке

Результаты поиска

Содержание WCX 1335

Отзывы:

Похожие инструкции для WCX 1335

Бренды по названию

Популярные бренды