background image

WESTELL.COM

Remote RMM-700 Installation Guide

Cautions and Warnings

1-800-377-8766

Page 5

Cautions and Warnings

Grounding and Electrical Safety

CAUTION:

Westell’s Kentrox equipment and peripherals contain electrostatic 
sensitive components. Proper handling, shipping, and storage precautions 
must be exercised.

CAUTION:

During installation, read and observe all additional Cautions and Warnings 
shown in Step 1: Install SIM Chip and Wireless Phone Module Hardware in 
Remote RMM-700, Step 4: Attach Chassis Ground, and Step 5: Connect 
DC Power Input.

Installation

CAUTION:

For Westell’s Kentrox equipment to operate safely and correctly, there 
must be a safety ground strap between the equipment ground bolts and 
the office ground.

Environment

CAUTION:

In the event that Remote RMM-700 has been subjected to adverse 
environmental conditions, a service inspection of Remote RMM-700 
should be made to ensure safe operation.

Restricted Access Locations

CAUTION:

The Remote RMM-700 is for use in restricted access locations only. 

FCC

The Federal Communications Commission has set limits for emitted radio interference, 
and Remote RMM-700 is constructed with this electromagnetic interference (EMI) 
limitation in mind. Remote RMM-700 is classified under FCC regulations as a Class A 
device, that is, a device for use in commercial environments and not in residential areas. 
This device has been tested and shown to comply with the following FCC rule: Part 15 
Subpart J. Operation of this equipment in a residential area may cause interference to 
radio and TV reception, requiring the user to take whatever steps are necessary to 
correct the interference.

Содержание Kentrox RMM-700




















Отзывы: