manualshive.com logo in svg

Wenger Gearboss Customizable Wood Lockers, Инструкции по установке и эксплуатации, Страница: 3 / 28

Поделиться
Скачать
Wenger Gearboss Customizable Wood Lockers Скачать руководство пользователя страница 3

3

Safety Precautions

Throughout this document you may find cautions and warnings which are defined as follows:

 

•  

WARNING:

  Failure to follow the instruction could result in serious injury or damage to property. 

•  

CAUTION:

  Failure to follow the instruction could result in minor injury or damage to property.

Read all of these safety instructions before assembling and installing any equipment.

Overview

•  This system should be installed only by skilled technical persons, and only after carefully reviewing these 

instructions.

•  It is suggested that the lockers are setup in a space that is large enough to safely handle the cartons, parts 

and accessories.

• 

Inspect the condition of the wall and floor where the lockers will be located. 

 

If the wall is not straight, establish a reference line so that the fronts of all lockers will line up.  

Also, determine the highest point on the floor, which will establish the leveled height of each row of lockers.

Before You Begin

•  Read the complete assembly procedure before beginning the assembly.

•  Hardware packs may contain extra fasteners that will not be required on your lockers.

•  At least two people are required to install the locker.

General Usage

•  Never hang from or climb on lockers.

•  Overloading or shock-loading lockers could cause a collapse, resulting in property damage or serious injury.

Installation Requirements

•  Lockers should be installed on an unfinished floor, tile or epoxy coated concrete flooring.

•  Any additional floor coverings are to be installed after the lockers to avoid interference with the floor levelers.

Before Installation

Make sure anyone installing 

the lockers has read and 

understands these instructions.

Failure to comply with 

Warnings and Cautions in this 

document can result in damage 

to property or serious injury.

To avoid damage and injury, 

more than one person is 

needed for installation.

Make sure the lockers are 

securely attached to walls 

or adjoining lockers after 

installation is complete.

Always wear safety glasses 

and gloves when assembling 

or installing the lockers.

Assemble and install the 

lockers only on flat, solid 

surfaces.

!

CAUTION

!

CAUTION

!

CAUTION

!

CAUTION

!

CAUTION

!

CAUTION

Содержание Gearboss Customizable Wood Lockers





























Отзывы:

Нет отзывов