Wenger Gearboss Customizable Wood Lockers Скачать руководство пользователя страница 10 | Manualshive

Страница: 10 / 28

Wenger Gearboss Customizable Wood Lockers Скачать руководство пользователя страница 10

10

Installation with Metal Base (continued)

4. Depending on the locker layout configuration, attach the bases to either a wall or the floor.

Wall Mount Installation

Attach each base to the wall using the attached wall mount bracket and the appropriate fasteners

and method described in the "Fasteners - Not Suppled" section.

Note:

If the wall is not straight, it may be necessary

to add shims behind some of the wall mount brackets.

Island Installation (Floor Mount)

Attach two bases back-to-back to the floor by placing an island base mount bracket over both

wall mount brackets and the appropriate fasteners and method described in the

"Fasteners - Not Suppled" section.

Island Base

Mount Bracket

(8)

Wall Mount

Bracket

Wall Mount

Bracket

Wall Mount

Brackets

Inferior or improperly installed

fasteners could cause the

locker to tip over.

!

WARNING

«
...
8
9
10
11
12
...
»

Содержание Gearboss Customizable Wood Lockers





























Отзывы:

Нет отзывов