Wen 56455i Скачать руководство пользователя | Manualshive

Страница: 37 / 52

background image

TROUBLESHOOTING GUIDE

WARNING!

Stop using the generator immediately if any of the following problems occur or risk serious

personal injury. If you have any questions, please contact customer service at

1-800-232-1195

(M-F 8-5 CST),

or email

[email protected]

.

PROBLEM

POSSIBLE CAUSE

SOLUTION

Engine will not

start.

3-in-1 switch is set to OFF.

Set 3-in-1 to ON.

Battery is out of power

Electric start will not work if battery is out of power. Start gen-
erator using the recoil start to charge the battery.

Oil is low.

Add or replace oil.

Battery is too cold

Store the generator in a warmer location.

Engine is out of fuel.

Add fuel.

Engine is filled with
contaminated or old fuel.

Drain fuel in the tank. Fill with fresh fuel.

Spark plug is dirty or broken.

Clean or replace the spark plug.

Carburetor is air locked.

Turn the 3-in-1 switch to OFF. Remove bolt from bottom of the
carburetor. Take off the carburetor bowl to allow it to reset.
Replace carburetor bowl and reinstall the bolt.

Ghost in the generator.

Persuade ghost to leave.

Engine runs but

there is no

electrical output.

Reset button is tripped due to
wattage overload.

Turn off and all unplug electrical devices. Wait 3 minutes, then

press the activated reset button to reset. Check the total wattage

of the devices and reduce the load if it exceeds the capacity of

the generator.

Bad connecting cords/wires.

Check power cords & extension cords. Do not use if any cord is
damaged. Replace damaged cords immediately.

Bad electrical device connected
to the generator.

Try connecting a different device.

Generator runs but

does not support all

electrical devices

connected.

AC or DC receptacles are over-
loaded, circuit breaker tripped

Turn off and unplug the electrical devices. Wait 3 minutes, then

press the circuit breaker to reset. Check the amperage of the

devices to make sure they are within the capacity of the recep-

tacles.

Short circuit in one of the de-
vices.

Disconnect any faulty or short-circuited electrical loads.

Air filter is dirty.

Clean or replace the air filter element.

Engine is

“Hunting” during

operation

(Engine RPM is

fluctuating).

1. The fuel isn’t running through
the fuel valve.
2. The air filter is clogged.
3. The muffler or spark arrester
is blocked
4. There is gunk in the carbure-
tor preventing a consistent fuel/
air mixture.

Turn off the generator and wait for it to cool down. Perform the
following steps:
1. Check if the fuel is properly and consistently going through
the fuel valve
2. Check for any blockage in the air filter. Check and clean the air
filter as necessary.
3. Check if the spark arrester is blocked. Clean with metal brush
as necessary.
4. Use “gunk remover” spray on the carburetor jets.

37

«
...
35
36
37
38
39
...
»

Содержание 56455i





















































Отзывы:

Нет отзывов

Похожие инструкции для 56455i

Бренд: CAMPAGNOLA Страницы: 120

Бренд: Titan Страницы: 11

Бренд: Westfalia Страницы: 34

Бренд: Generac Power Systems Страницы: 36

Бренд: Lenox Страницы: 23

Бренд: Ericsson Страницы: 34

Бренд: Honda Страницы: 59

Бренд: Lenox Страницы: 17

Бренд: Boston Acoustics Страницы: 2

Бренд: KNOVA Страницы: 24

Бренд: Domnick Hunter Страницы: 36

Бренд: Rohde & Schwarz Страницы: 91

Бренд: Robin Страницы: 32

Бренд: Robin Страницы: 46

Бренд: Panacom Страницы: 28

Бренд: Wagan Страницы: 7

Бренд: Ultra-Gen Страницы: 30

Бренд: Trevi Страницы: 32

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды