manualshive.com logo in svg

WELLTECH 2540 FXO, Руководство пользователя, Страница: 51 / 79

Поделиться
Скачать
WELLTECH 2540 FXO Скачать руководство пользователя страница 51

 

 

51 

following type. 

None:

 No display name will be used 

PSTN caller ID:

 The display name will be the collected PSTN 

caller ID 

SIP  display  name:

  The  display  name  will  be  the  Display 

Name set in this SIP trunk.   

FXO Tel NO:

 The display name will be the incoming FXO’s TEL 

No set on FXO lines. 

User  ID: 

The  SIP  caller  ID  will  be  used  according  to  the 

following type. 

 

SIP user ID: 

If the SIP user ID is set, the SIP user ID set in 

this SIP trunk will be used and the domain/SIP proxy will be 
the host part. The SIP FROM header’s URL will be the 

SIP_User_ID@Domain

 or 

SIP_User_ID@SIP_Proxy_Server

. 

 

PSTN caller ID: 

If the PSTN caller ID will be used in SIP URL, 

the SIP FROM header’s URL will be 

PSTN_Caller_ID@local_IP_address

. 

 

FXO Tel NO:

 If the FXO Tel NO will be used in SIP URL, the 

SIP FROM header’s URL will be 

FXO_Tel_NO@local_IP_address.

 

 
The following guideline could be used for most of case: 

1.

 

If the Welltech 2540 in SIP proxy is handled as a gateway, 
please set the display name and User Id should be set to 
“PSTN caller ID”. 

2.

 

If  the  Welltech  2540  is  SIP  proxy  is  handled  as  a 
subscriber, please set to the display name to “PSTN caller 
ID” and user ID to “SIP User ID”. 

   

 

For DNIS is Register TEL: 

When you have a call from VoIP to FXO to 

call out to PSTN network, there are two methods can be used.

   

 

Keep Alive:

 Enable or Disable it.

 

 

Keep Alive Time (sec): 

Specify of times send sip register message to 

proxy server. 

Содержание 2540 FXO
















































































Отзывы:

Нет отзывов