Wellcraft 270 Coastal Скачать руководство пользователя

Страница: 75 / 121

Proper storage is very important to prevent serious

damage to the boat. If the boat is to be stored indoors,

make sure the building has enough ventilation. It is very
important that there is enough ventilation both inside

the boat and around the boat.

• Check all hose clamps and make sure they are tight

and not corroded.

• Pump the antifreeze from the head, fresh and raw

water systems and flush several times with fresh

water.

Note: If the boat is to be stored indoors or

outdoors, open all drawers, clothes

lockers, cabinets, and doors a little. If
possible, remove the upholstery, clothing,

and rugs. Then hang a commercially

available mildew protector in the head

compartment.

• Check and lubricate the steering system.

• Clean and wash the boat.

• Install all upholstery, cushions and canvas.

After Launching:

14.3

Recommissioning

• Carefully check the engines and all water systems

and the engine bolts for leaks and proper operation.

•

Check the bilge pump manual and automatic

switches.

• Prime the fuel system and start the engines. When

each engine starts, check the cooling system port

below the engine cowling for a strong strean of
water. This ensures that the cooling pump is

operating.

Note: It is important and recommended that the

fitting out procedure for the marine gear
be done by a qualified marine technician.

Read the engine owner’s manual for the

recommended procedure.

• Carefully monitor the gauges and check for leakage

and abnormal noises.

• Operate the boat at slow speeds until the engine

temperature stabilizes and all systems are operating

normally.

Reactivating The Boat After Storage:

• Apply a fresh coat of bottom paint on the hull.

• Inspect all thru-hull fittings.

• Inspect the sacrificial anodes and install new anodes

if required.

• Install the propellers.

• Install the drain plug in the hull.

• Charge and install the batteries.

• Check the engines for damage and follow the

manufacturer’s instructions for recommissioning.

• Check the engine mounting bolts for the engines

and bracket to make sure they are tight.

• Perform all routine maintenance.

Содержание 270 Coastal


























































































































Результаты поиска

Содержание 270 Coastal

Отзывы:

Похожие инструкции для 270 Coastal

Бренды по названию

Популярные бренды

Wellcraft 270 Coastal, Руководство пользователя

Результаты поиска

Содержание 270 Coastal

Отзывы:

Похожие инструкции для 270 Coastal

Бренды по названию

Популярные бренды